manualshive.com logo in svg

Carrier 38UQZ016, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Carrier 38UQZ016 Скачать руководство пользователя страница 16

16

• 

If this type of installation is used, ensure that the units 
are not affected by flooding, snow accumulation or 
leaves.

• 

Ensure that the units are secured to prevent injuries 
to people handling or working on the units.

IMPORTANT: Rainwater, and in heat pump mode defrost 
water, is drained through the unit base. For this reason the 
units must be elevated above the concrete base to allow 
correct drainage.

•  

Rainwater and defrost water drainage

 

38UQZ units incorporate drillholes in the base in 
order to correctly drain any condensate or rainwater 
and defrost water which may enter the unit in the fan 
area. Ensure correct drainage.

•   Provide suitable vibration isolators to prevent noise 

transmission and vibrations during unit operation.

Fig. 12

• 

The 38UQZ models incorporate fixing holes in the 
base profile to attach the units to the floor.

•   38UQZ models can have several vibration isolator 

types, as shown in Fig. 13.

IMPORTANT: Units must be installed in accordance with 
applicable local, national and European installation and 
safety standards and regulations.

40ALZ indoor units

These units have been designed for indoor installation, 
connected to supply and return air ducts.

When selecting the installation site, observe the following 
points:
• 

Ensure that the condensate water collected in the drain 
pan is correctly evacuated.

• 

Leave sufficient clearance for installation and mainte-
nance (see Fig. 3 - Service clearances).

• 

If the units are not ducted, ensure that the return air is 
sufficient for the required air flow.

• 

See Table 1 - Physical Data, for unit weights and ensure 
that the installation surface can support the unit weight.

• 

In accordance with applicable standards and laws the 
unit can be suspended from the ceiling or floor-mounted 
(see Fig. 14).

Fig. 14

Vibration isolators

Vibration isolators

Unit

Hexagonal nut

Washer

Flexible mounting

Base

Unit

Flexible mounting

Washer

Spring washer

Hexagonal nut

PNL 40 x 40 x 4

PNU 80 x 45 x 6

100 mm

Concrete base

ROOF

Supply 

air

Supply 

air

ROOF

Vibration isolators

Base

Fig. 13

Fig. 11

Concrete base

Содержание 38UQZ016





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды