10
Important Information
Carrera DiGiTAL 132
EVOLUTiON
Carrera DiGiTAL 132
EVOLUTiON
Please note that Evolution (analog system) and Carrera DIGI-
TAL 132 (digital system) involve two separate and completely inde-
pendent systems. We hereby expressly indicate that both systems
must be kept separate when setting up the track, i.e. no connecting
rail from Evolution may be used together with the connecting rail
and Black Box of the Carrera DIGITAL 132, even if only one of the
two connecting rails (Evolution connecting rail or Carrera DIGI-
TAL 132 connecting rail and Black Box) is attached to the current
supply. Furthermore, no other Carrera DIGITAL 132 components
(switches, electronic lap counter, pit stop) may be built into an Evo-
lution course, i.e. via analog operation.
Non-compliance with the above information may result in damage
or destruction of the respective Carrera DIGITAL 132 components.
In this case no warranty may be claimed.
Positioning
receiver/tower
3 m
9.84 ft.
Receiving radius 3 m/9.84 ft.
1
3 m
9.84 ft.
3 m
9.84 ft.
2 m
6.56 ft.
2 m
6.56 ft.
1 m
3.28 ft.
2
The tower contains the infrared-receiver which passes on the sig-
nals of the infrared-transmitter (located in the WIRELESS speed
controller) to the Carrera DIGITAL 124/132 car. In order to be able to
receive the signals permanently the WIRELESS transmitter (speed
controller) should be kept at a maximum range of 3 metres from the
receiver/tower in visibility (cf. Fig.
1
and
2
). To achieve a larger
receiving radius a further receiver/tower can be connected to the
Black Box (cf. Fig.
2
).
Assembly instructions
1
4
2
3
1
+
2
+
3
Before assembling please insert the connecting clips
in the track as shown in figure
1
.
Stick tracks together on a flat
base. Move the connecting clips according to figure
2
in direction
of the arrow until they audibly snap in. The connecting clip may also
be inserted later. The connecting clips can be removed into both
directions by simply pressing down the clamped nose (see fig.
3
).
4
Fastening:
To fasten the track sections on a board, it is neces-
sary to use the track section fasteners (Item no. 85209, not con-
tained in the package).
Note:
Carpeting is not a suitable foundation on which to build the track be-
cause of static charging, formation of fluff and ready inflammability.
Guard Rails and Supports
1
2
3
4
1
Guard rails:
Guard rail mounts are fitted by tilting them upwards
onto the verge of the track.
2
+
3
Supporting raised sections:
The shank of the ball pivot is
to be inserted into the square slots provided on the underside of the
track. The supports can be made higher by using the extensions.
The pedestal of the supports can be screwed to a base if required
(screws not included).
4
Supporting steep curves:
Slanting supports of the right height are provided to support steep
curves. Fix the nonadjustable supports at the beginning and end of
the curves. Insert the heads of the supports in the round slots of the
underside of the track.
Electrical connection
1
1
Connect the transformer plug with the Black Box
Note:
To avoid short-circuits and electrocution, the toy may not be
connected using foreign devices, plugs, cables or other objects for-
eign to this toy. The Carrera DIGITAL 132 car racetrack only works
properly with an original Carrera DIGITAL 132 transformer.
The PC interface (PC Unit) may only be operated together with the
original Carrera PC Unit.
Car components
1
2
3
3
3
3
4
5
9
6
8
10
11
7
1
Body, spoiler
2
Engine
3
Tyres
4
Rear axle
5
Chassis
6
Guide keel
7
Double sliding contact
8
Front axle
9
Car board with reversing switch
10
Front light board
11
Rear light board
Note:
vehicle construction depends on the model.
The designation of the individual parts may not be used as
order numbers.
