12
Coding/decoding of the cars to
the according speed controller
2x CLICK
1
2
2x CLICK
3
Place car on the track, push lane-change-button twice fig.
1
, lift car
at the front, put car back again fig.
2
, while car´s lights are flashing
push lane-change-button twice fig.
3
. Programming is confirmed
by a tone. All settings are saved until new programming is carried
out.
Autonomous Car function
300
150
250
200
0
100
50
SPEED
+
CLICK
1
2
4x CLICK
Place car on the track, push lane-change-button twice, lift car at the
front, put car back again (see coding/decoding fig. 1 + 2). While
car´s lights are flashing push lane-change-button 4 times fig.
1
.
Start car, push lane-change-button for requested speed fig.
2
(irre-
spective of the car´s position). Autonomous car will drive at this
speed automatically and consistently until its decoding.
Decoding is effected by holding the car. For new coding see coding/
decoding.
Pace Car Funktion
Pit Stop 30346
300
150
250
200
0
100
50
6x CLICK
SPEED
+
CLICK
1
2
3
4
Place car on the track, push lane-change-button twice, lift car at the
front, put car back again (see coding/decoding fig. 1 + 2).
While car´s lights are flashing push lane-change-button 6 times fig.
1
.
Start car, push lane-change-button for requested speed fig.
2
(irrespective of the car´s position). Car will assume this speed consi-
stently and will enter the next Pit Stop automatically fig.
3
.
Start Pace Car function:
Start Pace Car by pushing the button at the Black Box fig.
4
. After
10 seconds each lane switch will change independently until the
Pace Car enters the Pit Stop. Carry out car decoding (see point
coding/decoding).
Setting basic speed
1
1 – 10
1 – 10
2
(individually for one and/or several cars)
Please note the following procedures:
1. Switch off Black Box, place car/s on the track, effect coding of
WIRELESS speed controller to speed controller 1 as per point „Co-
ding/Decoding“.
2. Switch on WIRELESS speed controller located on lower side
(ON/OFF switch).
3. Press and hold lane-change-button during Black Box is switched
on again. Don´t release the lane-change-button until the 1st LED
lights red. Levels are set by pushing lane-change-button. Confirm
speed by pressing the speed controller´s tappet (thumb) (=> middle
LED will light).
1
+
2
1 LED on = low speed
5 LEDs on = high speed
Setting braking effect
1
1 – 10
1 – 10
2
(individually for one and/or several cars)
Please note the following procedures:
1. Switch off Black Box, place car/s on the track, effect coding of
WIRELESS speed controller to speed controller 2 as per point „Co-
ding/Decoding“.
2. Switch on WIRELESS speed controller located on lower side
(ON/OFF switch).
3. Press and hold lane-change-button during Black Box is switched
on again. Don´t release the lane-change-button until the 1st LED
lights red. Levels are set by pushing lane-change-button. Confirm
braking effect by pressing speed controller´s tappet (thumb) (=>
middle LED will light). Before the start return speed controller to the
original connector!
1
+
2
1 LED on = low braking effect
5 LEDs on = high braking effec
Setting fuel tank capacity
Pit Stop 30346
1
2
1 – 10
1 – 10
3
(individually for one and/or several cars)
1
Activate fuelling function at the Black Box.
Please note the following procedures:
1. Switch off Black Box, place car/s on the track, effect coding of
WIRELESS speed controller to speed controller 3 as per point „Co-
ding/Decoding“.
2. Switch on WIRELESS speed controller located on lower side
(ON/OFF switch).
3. Press and hold lane-change-button
during Black Box is switched on again. Don´t release the lane-chan-
ge-button until the 1st LED lights red. Fuel capacity is set by pushing
lane-change-button. Confirm by pressing speed con-troller´s tappet
(=> middle LED will light).
Before the start return speed controller to the original connector!
2
+
3
1 LED on = low fuel capacity
5 LEDs on = full tank
Refuelling:
Depending on the fuel capacity the car´s lights start to flash after
some time, the car slows down and might start to stutter. For refuel-
ling enter the Pit Stop and release the speed controller´s tappet.
(Fuelling amount depends on car´s standing time in the Pit Stop).
a) Filling up: wait until car´s lights stop flashing.
b) Partial refuelling: start while car´s lights still flash.
c) Non-refuelling: car drives on at reduced speed.
Car programming from DIGITAL
132 to Evolution (analogue)
Place car on the Evolution track and push speed controller´s tappet
three times (thumb). Push the switch for changing the running direc-
tion acc. fig.
1
. For Carrera Digital 132 operation mode return the
switch to original position.
Replacement of double sliding
contact and guide keel
2 a
2 b
1
Observations:
• Il est recommandé d’enlever et de remplacer une seule tresse à
la fois.
• Ne jamais tirer le véhicule en arrière afin de ne pas endommager
la tresse double.
1
Retirer avec précaution la quille de guidage (Fig.
1
) de son
support.
2
Lors du remplacement de la tresse double, veiller à retirer
d’abord le frotteur supérieur
2
a
partiellement avant de pouvoir
retirer complètement la tresse double avec le frotteur
2
b
.
Procéder de la même façon pour le montage.