background image

Carmanah M850 & M860 Self-Contained LED Lantern Instructions 

v1.

1

 

Jan

 201

6

 

20 

Servicing 

Servicing should be performed in accordance with the standard cycle established for the aid.   

Ensure that the lens and solar panels are clean.  Wipe with a cloth dampened with mild soap and 
water, if necessary.  

Using either the tap-to-activate digital LED display feature or the information key on the IR 
remote programmer, check the battery state-of-charge:  Look for battery state-of-charge reading 
XXX (bAtt – SoC – XXX) in the digital LED display that will sequence immediately after 
lantern status information.  Battery state-of-charge must be at least 60%; if less than 60%, the 
lantern must be removed from service for charging and troubleshooting.  Since the two M800 
lanterns use different battery configurations and voltages (M850/60X = 6.3 volts, M860/200BC 
= 8.4 volts), we rely primarily on battery state-of-charge to determine the health and status of the 
battery.  However, battery voltage information can be useful when troubleshooting a discrepant 
lantern and reporting back to customer service technicians at Carmanah for assistance. 

Cover the lantern with a shroud, jacket, box, blanket, etc., to simulate darkness.  The lantern 
should flash on rhythm after a few seconds.  While covered, confirm that all five LEDs are 
operating (check the LEDs by looking around the lantern just above the lantern’s focal plane; 
DO NOT look directly into the lantern with your eye at the focal plane).  

Uncover the lantern.  It should stop flashing. 

Battery Service Life 

The expected battery life is highly dependent on temperature:  The higher the temperature, the 
shorter the expected battery life.  Battery recharge intervals (i.e., replacement intervals) range 
from four years in hot climates to ten years in cold climates.  Field units should recharge 
(replace) batteries at intervals shown in the table on the next page. 

A battery replacement kit can be ordered directly from Carmanah (see SECTION 6 below).  The 
battery kits contain a Cyclon battery pack, harness, battery hold-down plate, head/base gasket 
and washers (lantern base not included).  Detailed battery replacement instructions are included 
with each kit.  If the lantern fails due to a battery problem within the first year after purchase, 
contact Carmanah’s customer service department at 1-877-722-8877 for an RMA number before 
shipping the lantern back to them for repair or replacement. 

60X 

Battery 

Pack 

(6.3V) 

200BC 

Battery 

Pack 

(8.4V) 

All manuals and user guides at all-guides.com

Содержание M850



































Отзывы: