background image

Contents

PLEASE read this first

.......................................................... 2

Codes and standards........................................................... 2
201GAS burner at-a-glance ................................................ 3

Prepare site •  prepare burner •  mount burner

 .............. 4

Install gas piping .................................................................. 9
Wire burner ......................................................................... 10

Check system  •  start-up burner/appliance

 .................. 11

Perform checkout procedures  •  fill out certificate

..... 13

Maintenance and service procedures ........................... 16
Troubleshooting ................................................................. 17

Dimensions and mounting information

........................... 19

Replacement parts

............................................................. 20

Instruction manual

Ratings

Input

.................................................150,000 to 399,000 Btuh

Fuels

.........................................Natural gas or propane gas

 

Max. supply pressure ..........................14 inches w.c.

 

Min. supply pressure .............................5 inches w.c.

 

Manifold pressure...............................3.5 inches w.c.

Electrical

: Power ...........................................

120V/60 Hz/1-Phase

 Motor.....................................

1/6 or 1/4 HP, 3450 RPM

 Current ...................................

Approx. 2.5 or 4.4 amps

Ignition

........................Carlin Model 41800 solid state ignitor

Control

........

Carlin Model 60200FR microprocessor control

Agencies

:  ..........................................................................UL  Listed  

 

Installer/servicer

 — Except where specifically 

stated otherwise, this manual must be used only by a 

quali-

fied service technician

. (In the state of Massachusetts, this 

product must be installed by a licensed Plumber or Gas Fitter.) 
Failure to comply with this or other requirements in this manual 
could result in severe personal injury, death or substantial 
property damage.

 

User 

— Refer only to 

User’s Information

 booklet for 

information regarding operation of this burner. The burner 

Instruction Manual

 is intended only for your service techni-

cian. The burner and heat exchanger must be inspected and 
started at least annually by your service technician.

70 Maple Street 

East Longmeadow, MA  01028

Ph  413-525-7700 

Fx  413-525-8306

Carlin Combustion Technology, Inc.

T

ech

 

support

   800-989-2275

carlincombustion.com

©

 

Copyright 2011 — Carlin Combustion Technology, Inc.

Содержание 201GAS

























Отзывы: