Carl Goldberg Products Husky 400 Скачать руководство пользователя страница 3

Страница: 3 / 9

ITEMS NEEDED TO COMPLETE THIS AIRCRAFT

1 5 CHANNEL RADIO WITH 6 MICRO SER-

VOS. (WE USED 6 CHANNEL

FUTABA

RADIO WITH S3108 SERVOS AND

GREAT

PLANES

ELECTRICFLY RECEIVER W/O

SPEED CONTROL)

2 12” SERVO EXTENSIONS

1 ELECTRONIC SPEED CONTROL (WE

USED A

CASTLE CREATIONS

PHOENIX

25 BRUSHLESS SPEED CONTROL)

1 3 CELL LI-PO BATTERY (

GREAT PLANES

ELECTRICFLY 1500)

ULTRAFLY

BRUSHLESS MOTOR A/30/29

WITH 3.89 GEAR RATIO

GREAT PLANES

ELECTRIFLY PROP

ADAPTER 3MM APC LONG

APC

PROPELLER 9 X4.7 SLO FLYER

1 CA ACCELERATOR

1 1 OZ. BOTTLE CA MEDIUM GLUE

1 1/2 OZ. BOTTLE CA THIN GLUE

1 5 MINUET EPOXY

1 1/4” FOAM RUBBER

1 #2 X 1/4” SHEET METAL SCREW FOR

MOTOR(MIGHT BE REQUIRED FOR SOME
MOTOR INSTALLATIONS)

TOOLS AND SUPPLIES FOR ASSEMBLY

MODELING OR UTILITY KNIFE

WORK SURFACE (24" X48")

SMALL STANDARD & PHILLIPS SCREW-
DRIVERS

MASKING TAPE

NEEDLE NOSE PLIERS

24” RULER

FLEXIBLE STRAIGHT-EDGE

30-60-90° x 6" TRIANGLE

SOFT PENCIL

A FEW STRAIGHT OR "T" PINS

WIRE CUTTER (DYKES)

OPTIONAL HEAT GUN/COVERING IRON

ACID BRUSH

5 FT. LENGTH OF STRING

Caution:

Before starting, care-

fully go over all high

stress areas (Wing

bolt mounting blocks,

Firewall, landing gear

blocks, fuselage form-

ers, etc.) with an

epoxy or wood glue to

confirm all areas are

well glued.

We will not warranty

any of these parts.

Содержание Husky 400










Результаты поиска

Содержание Husky 400

Отзывы:

Похожие инструкции для Husky 400

Бренды по названию

Популярные бренды

Carl Goldberg Products Husky 400, Руководство пользователя

Результаты поиска

Содержание Husky 400

Отзывы:

Похожие инструкции для Husky 400

Бренды по названию

Популярные бренды