manualshive.com logo in svg

Carelink CL-MC-XE1-IP-Y, Руководство пользователя, Страница: 17 / 27

Поделиться
Скачать
Carelink CL-MC-XE1-IP-Y Скачать руководство пользователя страница 17

 CL-MC-XE1-IP-Y Series (1/2/4 E1) User Manual

 

- 14 - 

The CLI commands are summarized as the following table: 

 

Table 3-9.1 CLI Command Description 

CLI Command 

Description 

System Command 

logout 

Logout CLI System 

cdisp 

Display CL-MC-XE1-IP-Y current configurations. 

csave 

Save current configurations: CL-MC-XE1-IP-Y & relative setting. 

cload 

Load configuration setting from FLASH. 

passwd  

Enter password to change user-mode. (i.e. View/Setup/Admin mode) 

PS: If inputted password is not for "setup" or "admin", it will enter the "view" mode.

setpass mode 

Modify password for user-mode. 

mode: ‘s’ for setup mode, ‘a’ for admin mode, ‘c’ for CLI login 

ipset ip_addr net_mask 

gw_addr

 

Set NMS port IP address, subnet mask and gateway address. 

ip_addr: NMS port IP address to be assigned. 

net_mask: subnet mask of IP address. 

gw_addr: gateway IP address. 

Example: ipset 192.168.1.11 255.255.255.0 192.168.1.254 

ipget

 

Display NMS port current IP address. 

trapset mode trap_ip_addr 

Set SNMP Trap Mode & Host IP 

mode: 0 for disable SNMP trap, 1 for enable SNMP trap 

Example: trapset 1 192.168.1.200 

(enable SNMP trap function and set host 192.168.1.200 to receive the trap 

message) 

trapget 

Get SNMP Trap Mode & Host IP 

ntpset mode 

server_ip_addr 

Set NTP Enable Mode & NTP Server IP 

mode: 0 for disable NTP function, 1 for enable NTP function 

Example: ntpset 1 192.168.1.201 

(enable NTP function and set NTP server address to192.168.1.201) 

ntpget 

Get NTP Enable Mode & NTP Server IP 

upgrade tftp_server_ip 

file_name 

Upgrade SW image file from TFTP server 

tftp_server_ip: TFTP server IP address 

file_name: the file name of software image to be upgraded 

EX: upgrade 172.16.1.101 CL-MC-XE1-IP-Y_v100_f110418.bin 

backup tftp_server_ip 

file_name 

Backup the system configuration to TFTP server 

tftp_server_ip: TFTP server IP address 

file_name: backup file name 

EX: backup 172.16.1.101 CL-MC-XE1-IP-Y_co_backup_1 

restore tftp_server_ip 

Restore the backup system configuration from TFTP server 

www.carelink.com

Содержание CL-MC-XE1-IP-Y




























Отзывы:

Нет отзывов