Carel SmartCella 3PH, Быстрое руководство

Страница: 29 / 44

9
ENG
“SmartCella 3PH” +0500119IE - rel. 1.2 - 10.03.2017
1.7 Technical specifi cations
Specifi cations WP00B14A10 WP00B24A10 WP00B34A10 WP00B44A10 WP00B47B20 WP00B57B20
Power supply 400V 3~ +N+E 50/60Hz
Max compressor power 5.5HP 7.5HP
Protectors Power Disconnect
switch
40A
Evaporator, condenser and
defrost protection Circuit
breaker
10A 16A
Compressor protection Adjustable
motor
protector
1.6-2.5A 2.5-4A 4-6.3A 6.3-10A 10-16A
Auxiliary circuit protection Circuit
breaker
6A
Inputs Room temperature probe ST1 NTC
Defrost probe ST2 NTC
Door switch (or additional
probe) MS1 voltage-free contact, contact resistance < 10 Ω, closing current 6 mA
S3 (probe 3) NTC
Confi gurable digital input
(or additional probe) * DI3 voltage-free contact, contact resistance < 10 Ω, closing current 6 mA
NTC
Safety thermostat yes
Thermal overload evaporator fan yes
Evaporator / condenser / defrost
protection alarm
yes
Compressor / high pressure switch /
compressor Kriwan protection alarm
yes
Outputs Evaporator fan 230V 1~+N+E 500W 2.5A AC3 400V 3~+N+E 2kW 3.3A AC3
Condenser fan 230V 1~+N+E 800W 3.9A AC3 230V 1~+N+E 800W 3.9A AC3
Defrost 400V 3~+T 6kW 9A AC1 400V 3~+T 9kW 13A AC1
Light (or AUX, confi gurable) 230V 1~+N+E 800W 3.9A AC3 230V 1~+N+E 800W 3.9A AC3
Solenoid valve yes
Compressor oil heater yes
Tab. 1.c
* To be connected directly to terminals 11 and 12 on the electronic board.
1.8 Option part numbers
P/N Description
IROPZDSP00 remote display interface
IR00XGD000 remote repeater display
IROPZ485S0 RS485 serial card with automatic polarity recognition (+/-)
IROPZKEY00 parameter program. key with extended memory, 12 V
batteries
PSTCON0*B0 repeater display conn. cables (*: 1= 1.5 m; 3= 3 m; 5= 5m)
1.9 Assembly and connections
1.
With reference to the drilling template, drill the four fastening holes
in the wall:
•
Unscrew the six fastening screws on the front panel
•
Remove the front panel
•
Fix the panel to the wall using screws of suitable length, based on
the thickness of the wall
2. Connect the power cables, the load power cables, the probes and
the remaining inputs/outputs to the terminal block on the panel, as
shown in the wiring diagram (see page 10/11)
3. Before starting installation, the motor protector should be calibrated
based on eff ective compressor power consumption, with reference
to the compressor’s rated data
4. Arm the circuit breakers and the motor protector
5.
Close the front panel using the six screws
6. Power the panel on
7. Arm the main switch (yellow/red)
Warning
•
separate the power cables (power supply, loads) from the signal cables
(probes, digital inputs) and the serial cable
•
use cables that are suitably sized for the current they carry
•
connect the terminal marked PE to the mains power supply earth
•
after having powered the three-phase expansion, check correct
current draw of the various loads