Carefree TRAVEL'R Скачать руководство пользователя страница 2

P

ROPRIETARY 

S

TATEMENT

 

The Travel'r Patio Awning is a product of Carefree of Colorado, located in Broomfield, Colorado, USA.  The 
information contained in or disclosed in this document is considered proprietary to Carefree of Colorado.  
Every effort has been made to ensure that the information presented in the document is accurate and 
complete.  However, Carefree of Colorado assumes no liability for errors or for any damages that result 
from the use of this document. 

The information contained in this manual pertains to the current configuration of the models listed on the 
title page.  Earlier model configurations may differ from the information given.  Carefree of Colorado 
reserves the right to cancel, change, alter or add any parts and assemblies, described in this manual, 
without prior notice. 

Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado 
products only.  Any other reproduction or translation of this document in whole or part is strictly prohibited 
without prior written approval from Carefree of Colorado. 

S

AFETY 

I

NFORMATION

 

 

This is the safety alert symbol.  It is used to alert individuals to potential 
personal injury hazards.  Obey all safety messages that follow this symbol to 
avoid possible personal injury or death. 

 

WARNING

 

Indicates a hazardous situation, which if not avoided, could result in death or 
serious bodily injury. 

  

CAUTION

 

Indicates a hazardous situation, which if not avoided, may result in minor or 
moderate bodily injury. 

 NOTICE

 

Indicates a situation that may result in equipment-related damage. 

General Safety: 

 

 

WARNING

  Shock Hazard.  Always disconnect battery or power source before 

working on or around the electrical system. 

 

 

WARNING

  Always wear appropriate safety equipment (i.e. goggles). 

 

 CAUTION  

Always use appropriate lifting devices and/or helpers when lifting or 

holding heavy objects. 

NOTICE  

When using fasteners, do not over tighten.  Soft materials such as fiberglass and 

aluminum can be "stripped out" and lose the ability to grip and hold. 

CALIFORNIA PROPOSITION 65 

 

WARNING

  This product contains chemicals known to the state of California to cause 

cancer or birth defects or other reproductive harm.  California’s Proposition 65 requires this 
warning to be given to customers in the state of California. 

Reference Publications located at 

www.carefreeofcolorado.com

052540-002  Travel'r, Installation Manual 
052540-102  Travel'r Arm Extension Installation Supplement 
052540-201  Travel'r, Owner's Manual 
052540-301  Travel'r, Service Manual 
052584-301  LED Service Manual for Vertical Arms Manual 

 

Carefree of Colorado 

www.carefreeofcolorado.com a

 Scott Fetzer 

company

 

Содержание TRAVEL'R

















Отзывы: