background image

REMOVING:

Press here 

to remove

Your headset can be removed for charging 

and storage by pressing your finger 

gently against the tab and sliding the 

headset up with the other hand.
We recommend that you remove the 

headset from the helmet when not in 

use.

USING THE HEADSET

GENERAL USAGE

GENERAL FUNCTIONS

DESIRED RESULT:

REQUIRED ACTION:

Turn on the 

headset

Press the CTRL Button steadily for at least three 

seconds

Turn off the 

headset

Press the CTRL Button steadily for at least three 

seconds

Increase the 

volume

Short press the Volume Up Button

Decrease the 

volume

Short press the Volume Down Button

AGC (Automatic Gain Control): In addition to manual Volume Control, 

the 

scala rider Q2 

pro

 will automatically increase and reduce its 

volume according to ambient noise and driving speed.

AUDIO SOURCES AND PRIORITIES

The different Audio Sources that are connected to the 

scala rider Q2  

pro

 are prioritized as follows:

Highest

  1. Mobile phone Audio / GPS device (Incoming/outgoing calls , 

 

    GPS audio and navigation instructions)

    2. Primary Buddy Audio and Secondary Buddy Audio

    3. A2DP audio source

   

4. FM Radio (built-in)

Lowest

  5. MP3 Connectivity (corded connection)

A high priority Audio Source will always interrupt any lower priority 

Audio Source. 

 

i.e.  

Mobile phone call interrupts Intercom call

 

 

Intercom call interrupts FM Radio

USING THE INTERCOM 

Making Intercom calls

To start a Buddy Intercom call with the Primary Buddy

 while 

the headset is on Standby you can either:

VOICE CONNECT: 
Start talking 

A Buddy Intercom call will be 

established and stay on until 

both sides are quiet for 30 

seconds. 

MC BUTTON CONNECT: 
Single tap the MC Button 

A Buddy Intercom call will 

be established. To end the 

Buddy Intercom call, single 

tap the MC Button again.

To start a Buddy Intercom call with the Secondary Buddy

 

while the headset is on Standby:

MC BUTTON CONNECT:
Double tap the MC Button 

A Buddy Intercom call will be established. To end the 

Buddy Intercom call, double tap the MC Button again.

NOTE: While the Intercom is on, the Redial and Voice Dial functions will 

be disabled

or

MC Button

En

glis

h

9

scala rider

®

 Q2

 MultiSet 

pro

Содержание SCALARIDER Q2 MULTISET PRO

















Отзывы: