background image

STATEMENT OF LIMITED WARRANTY 

Detecto Scale warrants its equipment to be free from defects in 
material and workmanship as follows: Detecto warrants to the 
original purchaser only that it will repair or replace any part of 
equipment which is defective in material or workmanship for a
period of one 

(1) year

 from date of shipment. Detecto shall be the 

sole judge of what constitutes a defect. 

During the 

first ninety (90) days

 Detecto may choose to supply all 

necessary replacement parts and service during normal weekday 
working hours at no charge to the buyer. 

After the first ninety (90) days

 Detecto will supply parts and 

service at the job site provided the owner agrees to pay the Dealer 
for all travel time, including mileage and test equipment, as well as 
any expenses incurred over the direct labor of the technician at the 
job site. This limited warranty honors only labor performed by 
Detecto authorized dealers. 

This warranty does not apply to peripheral equipment not 
manufactured by Detecto; this equipment will be covered by certain 
manufacturer’s warranty only. 

This warranty does not include replacement of expendable or 
consumable parts. This does not apply to any item which has 
deteriorated or damaged due to wear, accident, misuse, abuse, 
improper line voltage, overloading, theft, lightning, fire, water or acts 
of God, or due to extended storage or exposure while in purchaser’s 
possession. This warranty does not apply to maintenance service. 
Purchased parts will have a ninety (90) day repair or replacement 
warranty only. 

Detecto may require components be returned to the factory; they 
must be properly packed and shipping charges prepaid. A return 
authorization number must be obtained for all returns and marked  
on the outside of all returned packages. Detecto accepts no 
responsibility for loss or damage in transit. 

8525-M041-O1 Rev K 

x

 8430 Series 

16

Содержание Detecto 8430 Series





















Отзывы: