background image

 

CWF, BWF, RWF 

 

 

O

PERATION

 

 

The instructions for operating the temperature controller are given in a separate manual.   

 

If the furnace is fitted with a time switch, see also the supplementary manual MS03. 

 

If cascade control is fitted, see the supplementary manual MS07. 

3.1 

Operating Cycle 

 

The furnace is fitted with a combined Supply light and Instrument switch. The light is on 
whenever the furnace is connected to the supply. The switch cuts off power to the control circuit.  

 

Connect the furnace to the electrical supply. The Supply light should glow. 

 

Operate the instrument switch to activate the temperature controller; the 

O

 position is 

off

, the 

I

 position 

on

. The controller becomes illuminated and goes through a short test cycle. 

 

Close the furnace door and adjust the temperature controller – see the controller manual. 

 

Overtemperature option only.

 If the overtemperature controller has not yet been set as required, 

set it and activate it according to the instructions in the appropriate manual. 

 

Unless a time switch is fitted and is off, the furnace starts to heat up. The Heat light(s) glow 
steadily at first and then flash as the furnace approaches the desired temperature or a program 
setpoint. 

 

Overtemperature option only.

 If the overtemperature trip operates then an indicator in the 

overtemperature controller flashes, and the heating elements are isolated. Find and correct the 
cause before resetting the overtemperature controller according to the instructions supplied. 

 

To switch the furnace off, set the Instrument switch to 

O

. If the furnace is to be left off, isolate it 

the electrical supply. 

3.2 

General Operating Notes 

 

Heating element life is shortened by use at temperatures close to maximum. Do not leave the 
furnace at high temperature when not required. The maximum temperature is shown on the 
furnace rating label and on the back page of this manual. 

 

When heating large objects, in particular poor conductors, avoid shielding the thermocouple from 
the heating elements. The thermocouple is intended to sense the temperature near the heating 
element, but if a large object is placed in the chamber it may record the average temperature of the 
object and the elements, which can lead to overheating of the elements. Allow large objects to 
gain heat at a lower temperature and then reset the controller to a temperature close to the desired 
maximum. 

 

When heating materials which produce smoke or fumes, the chimney must be correctly fitted and 
unobstructed. Otherwise, soot accumulates in the chamber and could possibly cause an electrical 
breakdown of the heating element.  

 

If the furnace is used to heat materials which emit smoke or fumes, regularly heat it up to 
maximum temperature for one hour without load to burn away the soot.  

 

Materials such as case hardening compounds and other reactive salts may penetrate the furnace 
chamber lining and attack the wire elements, causing premature failure. Use of a hearth tile may 
be advisable: please consult our technical department. 

3.3 

MF02 

Содержание BWF

















Отзывы: