Car Show CS-MUST10 Ford Mustang Скачать руководство пользователя

Страница: 6 / 15

CarShow Installation Guide - Ford Mustang

CarShow

Installation Guide

CS-MUST-IG Rev A

Page 6

AC Module Removal

NOTE:

Removing this module is necessary to remove OEM Radio as it aids in the removal

of harnesses at back of radio. The module also needs to be relocated

before

installation.

(Shown in step 7)

The AC module is

EXTREMELY

fragile.

-Installer assumes all liability if AC module is damaged-

AC Module Removal

Carefully un-mount AC module by pulling up.

Unplug harness. Use extreme caution.

Remove Radio Mounting Bolts

Remove 4 x 7mm radio mounting bolts

Remove OEM Radio Unit

Carefully remove oem radio unit

**NOTE:

Harnesses are

extremely

short so use

caution

!!**

Unplug OEM Radio Unit

Carefully unplug radio harnesses, antenna and Sat

Radio antenna from back of OEM radio unit.

**NOTE:

Harnesses are

extremely

short so use

caution

!!**

CAUTION

Содержание CS-MUST10 Ford Mustang















Результаты поиска

Содержание CS-MUST10 Ford Mustang

Отзывы:

Похожие инструкции для CS-MUST10 Ford Mustang

Бренды по названию

Популярные бренды

Car Show CS-MUST10 Ford Mustang, Руководство по установке

Результаты поиска

Содержание CS-MUST10 Ford Mustang

Отзывы:

Похожие инструкции для CS-MUST10 Ford Mustang

Бренды по названию

Популярные бренды