Car Show CS-MUST10 Ford Mustang Скачать руководство пользователя

Страница: 12 / 15

CarShow Installation Guide - Ford Mustang

CarShow

Installation Guide

CS-MUST-IG Rev A

Page 12

Snap Radio Face Assembly Into Place

Carefully snap radio face assembly into place.

Then, with the connectors Fully Engaged, turn the

vehicle on and verify system powers up.

ENABLE INSTALLER SETTINGS

You will need to select certain settings based on any Optional Equipment that you may have

installed

STEP

Launch the Setting Screen

From the AM/FM screen,

select “Settings” in the upper

left hand corner

Select the individual Settings as needed

for the installed components

Selectable options vary by product and installation.

Select the options as applicable for the installed optional

components.

Содержание CS-MUST10 Ford Mustang















Результаты поиска

Содержание CS-MUST10 Ford Mustang

Отзывы:

Похожие инструкции для CS-MUST10 Ford Mustang

Бренды по названию

Популярные бренды

Car Show CS-MUST10 Ford Mustang, Руководство по установке

Результаты поиска

Содержание CS-MUST10 Ford Mustang

Отзывы:

Похожие инструкции для CS-MUST10 Ford Mustang

Бренды по названию

Популярные бренды