CaptiveAire RTULink Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 56

background image

21

Powered Exhaust Coil Signal ON/OFF (24VAC)

If the RTULink will be using 24VAC
as the control signal for a powered
exhaust, it must be configured to
accommodate this feature.  View
the FUNCTIONALITY section of this
manual to determine how to enable
a powered exhaust output and how
to change the settings that are
associated with it.  If configured, the
24VAC powered exhaust signal will
use the AUX and C terminals on the
“RTU” side of the RTULink as HOT
and NEUTRAL respectively.

is a wiring schematic for a

powered exhaust connected to AUX
and C terminals. Standard 18-2
wire should be used for output
wiring.

Note: This is a low voltage, low
amperage powered exhaust coil
signal that does not provide
power to the powered exhaust, it
only signals an ON/OFF state.

Powered Exhaust (0-10VDC)

If the RTULink will be using a 0-10VDC
as the control signal for a powered
exhaust, it must be configured to
accommodate this feature. Determine
which 0-10VDC output on the

“RTU”

side of the RTULink will be used to
control the powered exhaust.

is a wiring schematic for a powered

exhaust connected to Output #2. View
the FUNCTIONALITY section of this
manual to determine how to enable a
powered exhaust 0-10VDC output and
how to change the settings that are
associated with it. Standard 18-2 wire
should be used for output wiring.

Note: This is a low voltage, low
amperage control signal that does
not provide power to the powered
exhaust but signals a variable speed

Figure 25. RTULink - Powered Exhaust Connected to Output #2 (0-10VDC)

Figure 24. RTULink - Powered Exhaust Coil Signal (24VAC Signal)

«
...
19
20
21
22
23
...
»

Содержание RTULink

























































Отзывы:

Нет отзывов

Похожие инструкции для RTULink

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: ABB Страницы: 6

Бренд: ACS Страницы: 56

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Modulate Страницы: 2

Бренд: Keithley Страницы: 42

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: JB-Lighting Страницы: 60

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды