Instruction manual DI652
9
Please keep this instruction manual for future reference
P R O D U C T O V E R V I E W
C O N T R O L PA N N E L
USING YOUR DISHWASHER
Control Panel
Operation (Button)
Power
Delay -/+
Function
Press the button to turn on your dishwasher,the screen lights up.
Press the “+”button to add the delay time or press the “-”button
to decrease the delay time, maximum 24 hours delay can be
defined.
Press the button to select a function, corresponding indicator will
be lit.
4
1
3
4
Alt
Press the button to select either upper basket or lower basket
loaded, and the response indicators will be lit.
5
2
3
1
6
8
7
7
9
10
4
5
Program
Press the “ ”
or
“ ”
button to select a program, and the
corresponding indicator will be lit.
2
B U T TO N O P E R AT I O N
1
P OW E R
Press the button to turn on your dishwasher, the screen lights up.
2
P R O G R A M
Press the “ ” or “ ” button to select a program, and the corresponding indicator
will be lit.
3
D E L AY + / -
Press the “+”button to add the delay time or press the “-”button to decrease the delay
time, maximum 24 hours delay can be defined.
4
F U N C T I O N
Press the button to select a function, corresponding indicator will be lit.
5
A LT
Press the button to select either upper basket or lower basket loaded, and the response
indicators will be lit.
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1.
Open the door and switch on the appliance
2.
P
Program
“ ”
3.
Program
“ ”
4.
Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the
button
for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the
button
to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
Mmol/l
Water softener level
British
Clarke
WATER HARDNESS
7
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1.
Open the door and switch on the appliance
2.
P
Program
“ ”
3.
Program
“ ”
4.
Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the
button
for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the
button
to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
Mmol/l
Water softener level
British
Clarke
WATER HARDNESS
7
