Canvas 085-1572-0, Руководство по сборке

Страница: 7 / 36

12 Product No. 085-1572-0 | Model No. FHWS80023A
1.
This fire table comes equipped with a standard LP gas hose and regulator
including the appliance side connection for a CGA No 791 Cylinder Connection
Device. The LP gas hose and regulator supplied with this fire table must be used.
Only a hose and regulator specified by manufacturer can be used for replacement.
a.
The CGA No 791 connection incorporates a magnetic flow limiting device
that acts to limit the flow of gas if a leak is detected between the regulator
and the burner valve.
b.
If the burner valve is open prior to the LP gas cylinder service valve being
opened, the connection will interpret this free flow of gas to be a leak.
c.
The connection safety feature will reduce gas flow from the regulator to
the appliance to a minimal level.
d.
Be sure that the burner control valve is closed prior to opening the LP gas
cylinder service valve to ensure that the connection flow limiting device is not
triggered mistakenly.
e.
If the connection flow limiting device is triggered mistakenly, close the LP
gas cylinder service valve and the burner valve, wait 10 seconds to allow the
device to reset, open the cylinder service valve, then open the burner valve
and light the fireplace as per lighting instructions.
2.
Be sure to protect the hose from any hot surfaces. Serious danger may result if the
hose contacts any hot surface.
3.
Regular maintenance of the hose and regulator:
a.
Inspect the hose before each use of the fire table. If the hose shows signs
of cracks, abrasions, cuts or damage of any kind, do not operate the appli-
ance. Fix or replace the hose as required before using the appliance. For
assistance with repair or replacement of the hose, call the service centre at
1-888-670-6684. Use only replacement parts from the manufacturer.
b.
Inspect the seal inside the CGA No 791 service valve on the LP gas cylinder
when replacing the cylinder or at least once per year. If there is any indication
of damage, have the seal replaced by a certified gas dealer before operating
the appliance.
4.
Do not use tools to tighten the CGA No 791 connection nut onto the LP gas
cylinder service valve. Hand tighten only.
5.
Be careful to not cross the threads on the connection when tightening the CGA No
791 connection onto the LP gas cylinder service valve.
6.
“Leak Test” should always be performed after attaching the connection to the LP
gas cylinder service valve. (See “Checking for Leaks” section of this manual on Step
7, page 19.)
7.
For the connection of the hose and regulator to the LP tank, refer to Step 5 on
page 18.
GLASS BEADS WARNING:
1.
Glass media may have sharp edges. Wear safety glasses and gloves when handling.
2.
Do not change or substitute the glass media material provided with this fire pit. If
replacing, use only replacement glass media available from your local authorized
dealer/distributor.
3.
Pour the glass media evenly in to the burner area (with the exception of the
screen—if applicable). The glass should be 1/2 to 1” (1.2 to 2.5 cm) above the burner.
4.
IMPORTANT:
Do not exceed a height of 1" (2.5 cm) above the burner when
placing glass media. Ensure no media covers the igniter screen. Store any excess glass
media in a safe location.
5.
Keep away from the unit for the first 20 minutes after igniting your unit for the first
time, as lava rocks/pumice stones /glass beads could pop out and cause injury. Should
any media pop out, discard them.
6.
Always ensure that lava rocks/pumice stones/glass shards/glass beads are
completely dry before use. Failure to do so will cause them to crack or pop.
IMPORTANT SAFETY INFORMATION
HOSE AND REGULATOR ASSEMBLY AND REPLACEMENT
DO NOT PLACE ANY
MEDIA ON SCREEN
13
IMPORTANT SAFETY INFORMATION