22
23
ENG
Troubleshooting
Here is an overview of the most common problems. if you have any further questions please contact your Canton dealer,
call our Service Hotline on +49 (0) 60 83 28 70 or send us an e-mail at [email protected].
Problem
Possible cause
Solution
DM system does not turn
on
1. Power cable not connected to the power outlet and /
or DM system
Check connection
2. The power has not been turned on
Switch to “ON”
Sound reproduction too soft
1. Volume of DM system set too low
increase the volume using the “Volume” button
DM system does not
respond to remote control
1. The battery is flat
Change the battery
No sound reproduction
1. Sound format of the source device wrongly selected
(Digital input „AuX“)
1. Please check the correct setting of your source device (see Page 6).
„DTS“ or „Dolby Digital“ coded output formats cannot be reproduced
2. Source device not producing any signal
2. Digital output on the source device not activated (please refer to device instructions)
3. Cable not correctly connected / faulty cable
3. Check the connection of the source device to the DM 8.2 and
change the cable where necessary
DM system hums
1. Signal lines from source device to DM system too long
use shorter signal line
2. Signal line used is not fault-protected or the protection
has been damaged (defective)
Change signal line for a fault-protected line
3. ground loop (ripple pickup) generated
A ground loop can be generated when two or more devices connected via a signal
line (cinch) are plugged into separate sockets (e. g. amplifier and computer). Plug all
devices connected to the DM 8.2 into a multiple socket output using safety plugs
4. Another piece of equipment on the same circuit has no
interference suppression (e. g. fridge)
Switch off possible sources of interference to test; unplug the device concerned to see
if the humming noise disappears or connect the source of interference to a different cir-
cuit (l1, l2 or l3). (Where necessary take advice from your electrician.) insert a special
“ferrite common mode filter” (available from specialist retailers) between the amplifier
and the DM system to eliminate the humming. Turn the power plug round to reduce the
so-called ripple voltage (particularly important if the source device is not earthed)
ENG
Display
The DM system has a multifunctional display that
lights up blue for approx. 5 seconds in response to
a remote control command. The possible readouts
and their meanings are shown below. The standby
mode of the DM system is indicated by a red leD
light.
FRA
Affichages display
le système DM System dispose d’un
display multifonctions qui, sur commande
de la télécommande, s’éclaire en bleu pour
env. 5 secondes. les affichages possibles
et leur signification sont listés ici. le mode
stand by du système DM est indiqué par
une leD rouge allumée.
ESP
Indicaciones en la pantalla
el sistema DM dispone de una pantalla
multifuncional que se enciende de color
azul durante aproximadamente 5 segun-
dos cuando recibe el comando desde el
mano a distancia. Aquí se enumeran las
posibles indicaciones y su significado. el
modo standby del sistema DM se indica
mediante un leD rojo.
ENG
TV input (analogue)
FRA
entrée TV (analogique)
ESP
entrada TV (analógica)
TV
ENG
AuS input (digital)
FRA
entrée AuX (numérique)
ESP
entrada AuX (digital)
AUX
ENG
DVD input (analogue)
FRA
entrée DVD (analogique)
ESP
entrada DVD (analógica)
DVD
ENG
Volume (00 – 60)
FRA
Réglage de volume (00 – 60)
ESP
Regolación del volumen acústico
(00 – 60)
30
ENG
Mute
FRA
Mute
ESP
Mute
–––
ENG
Play Mode Stereo
FRA
Play Mode Stereo
ESP
Play Mode Stereo
ST
ENG
Play Mode Surround
FRA
Play Mode Surround
ESP
Play Mode Surround
SUR
ENG
Sound Mode loudness
FRA
Sound Mode loudness
ESP
Sound Mode loudness
LOU
ENG
Sound Mode Off
FRA
Sound Mode (mode sonorité)
non activé
ESP
Sound Mode (modo de sonido)
desonectado
BYP
ENG
Sound Mode Voice
FRA
Sound Mode Voice
ESP
Sound Mode Voice
VOI
