manualshive.com logo in svg

Canon PIXMA MX310 series, Руководство по обслуживанию, Страница: 7 / 25

Поделиться
Скачать
Canon PIXMA MX310 series Скачать руководство пользователя страница 7

##220 

TX / RX 

System error (main program hang-up) 

##224 

TX / RX 

An error has occurred in the procedure signal in G3 transmission. 

##226 

TX / RX 

The stack pointer has shifted from the RAM area. 

##229 

RX 

The recording area has been locked for 1 minute. 

##232 

TX 

The encoder control unit has malfunctioned. 

##237 

RX 

The decoder control unit has malfunctioned. 

##238 

RX 

The print control unit has malfunctioned. 

##261 

TX / RX 

A system error has occurred between the modem and the system 

control board. 

##280 

TX 

Re-transmission of the procedure signal has been attempted the 

specified number of times, but failed. 

##281 

TX 

Re-transmission of the procedure signal has been attempted the 

specified number of times, but failed. 

##282 

TX 

Re-transmission of the procedure signal has been attempted the 

specified number of times, but failed. 

##283 

TX 

Re-transmission of the procedure signal has been attempted the 

specified number of times, but failed. 

##284 

TX 

After TCF transmission, DCN has been received. 

##285 

TX 

After EOP transmission, DCN has been received. 

##286 

TX 

After EOM transmission, DCN has been received. 

##287 

TX 

After MPS transmission, DCN has been received. 

##288 

TX 

After EOP transmission, a signal other than PIN, PIP, MCF, RTP, 

RTN has been received. 

##289 

TX 

After EOM transmission, a signal other than PIN, PIP, MCF, RTP, 

RTN has been received. 

##290 

TX 

After MPS transmission, a signal other than PIN, PIP, MCF, RTP, 

RTN has been received. 

##670 

TX 

In V.8 late start, the DIS V.8 ability from the receiving machine was 

detected, and CI was sent in response; however, the procedure 

failed, causing T1 time-over. 

##671 

RX 

In V.8 call reception, the procedure fails to proceed to phase 2 after 

CM detection, causing T1 time-over. 

##672 

TX 

In V.34 transmission, the procedure fails to proceed from phase 2 to 

phase 3 or later, causing T1 time-over 

##673 

RX 

In V.34 reception, the procedure fails to proceed from phase 2 to 

phase 3 or later, causing T1 time-over 

##674 

TX 

In V.34 transmission, the procedure fails to proceed from phase 3 or 

4 to the control channel or later, causing T1 time-over 

##675 

RX 

In V.34 reception, the procedure fails to proceed from phase 3 or 4 to 

(7/32) 

Содержание PIXMA MX310 series


























Отзывы:

Нет отзывов