Canon PIXMA MP950 Скачать руководство пользователя страница 6

Страница: 6 / 55

1. MAINTENANCE

1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement

Consumables by Service Engineer

(1) Adjustment

Note: DO NOT loosen the red screws at both ends of the carriage shaft, securing the print head position, as they are not re-

adjustable.

The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor unit.

Only for CD / DVD printing supported regions.

(2) Periodic maintenance

No periodic maintenance is necessary.

(3) Periodic replacement parts

There are no parts in this machine that require periodic replacement by a service engineer.

(4) Replacement consumables

There are no consumables that require replacement by a service engineer.

Adjustment

Timing

Purpose

Tool

Approx.

time

EEPROM reset

At logic board replacement

To reset each setting

None.

Perform in the
service mode.

1 min.

LCD language
settings

At logic board replacement

To set the language to be displayed
on the LCD.

None.

Perform in the

user mode.

1 min.

Destination setting

(EEPROM settings)

At logic board replacement

To set destinations

None.

Perform in the
user mode.

1 min.

Waste ink counter
resetting

(EEPROM settings)

- At logic board replacement

- At waste ink absorber

replacement

To reset the waste ink counter.

None.

Perform in the

service mode.

1 min.

Waste ink amount
settings

(EEPROM settings)

- At logic board replacement

- At waste ink absorber

replacement

To set the waste ink amount to the
waste ink counter.

None.

Perform in the
service mode.

1 min.

Paper feed motor
position adjustment

At paper feed motor
replacement

To adjust the belt tension. (Position
the paper feed motor so that the belt
is stretched tight.)

None.

2 min.

CD / DVD detection
sensor light volume
correction

- At logic board replacement

- At carriage unit replacement

To correct the light volume for the
CD / DVD detection sensor.

None.

Perform in the
service mode.

2 min.

Grease application

- At carriage unit replacement

- At PR shaft ass'y

replacement

- At CL base or CL gear

replacement

- To maintain sliding properties of

the carriage shaft and the lift cam
shaft.

- To protect the machine's sliding

portions (gears).

FLOIL KG-107A

1 min.

New Ink system function

check

- At logic board replacement

- At platen unit replacement

- At carriage unit replacement

To maintain detection functionality
for presence of the ink tanks and
each ink tank position.

None.

Perform in the
service mode.

1 min.

FAU sponge sheet
position

- At FAU sponge sheet

replacement

- At FAU sponge frame

replacement

- At scanning unit replacement

To position the FAU sponge sheet

None.

2 min.

1-1

Содержание PIXMA MP950
























































Результаты поиска

Содержание PIXMA MP950

Отзывы:

Бренды по названию

Популярные бренды

Canon PIXMA MP950, Руководство по обслуживанию

Результаты поиска

Содержание PIXMA MP950

Отзывы:

Бренды по названию

Популярные бренды