Canon PIXMA MP950 Скачать руководство пользователя страница 33

Страница: 33 / 55

5) Press the ON/OFF button to complete a button and LCD test and to return to the service mode menu selection.

Set the waste ink amount data to a replaced new EEPROM after the logic board is replaced in servicing.

1) Before replacement of the logic board ass'y, check the waste ink amount in EEPROM information print.

[See 3-4. Verification Items, (2)

EEPROM information print.]

2) In the waste ink amount setting mode, press the Stop/Reset button the specified number of time(s) according to the waste ink absorber whose

value should be transferred to the replaced new EEPROM. (Only the main waste ink absorber for the MP950)

3) Press the ON/OFF button to proceed to the next step.

4) The waste ink amount can be set in 10% increments by pressing the Stop/Reset button. Press the Stop/Reset button the appropriate number of

time(s) to select the value which is closest to the actual waste ink amount.

Time(s)

Waste ink absorber

Remarks

0 times

Main waste ink absorber

1 time

Platen waste ink absorber

Not valid for the MP950

2 times

Both the main and platen waste ink absorbers

Only the main waste ink absorber is valid for the MP950

3 times or more Not valid

Press the ON/OFF button to return to the waste ink amount setting
mode.

Time(s)

Waste ink amount value to be set (%)

0 times

1 time

10%

2 times

20%

3 times

30%

4 times

40%

1-28

Содержание PIXMA MP950
























































Результаты поиска

Содержание PIXMA MP950

Отзывы:

Бренды по названию

Популярные бренды

Canon PIXMA MP950, Руководство по обслуживанию

Результаты поиска

Содержание PIXMA MP950

Отзывы:

Бренды по названию

Популярные бренды