Canon PIXMA MP620 series Скачать руководство пользователя страница 15

Страница: 15 / 46

3. REPAIR

3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)

MP620 / MP628

TABLE OF CONTENTS

Service part

Notes on replacement

Adjustment / settings

Operation check

Logic board ass'y

- Before removal of the logic board

ass'y, remove the power cord,
and allow for approx. 1 minute
(for discharge of capacitor's
accumulated charges), to prevent
damages to the logic board ass'y.

- Before replacement, check the

ink absorber counter value (by
service test print or EEPROM
information print).

After replacement:

1. Initialize the EEPROM.
2. Set the ink absorber counter

value.

3. Set the destination in the

EEPROM.

4. Check the ink system function.
5. Perform LF / Eject correction.
6. Perform button and LCD test.

Perform 1 to 6 in the service
mode.
[See

3-3. Adjustment /

Settings, (6) Service mode

, for

details.]

7. Perform print head alignment

and LCD language setting in
the user mode.

8. Reset the LAN settings in the

user mode.

- EEPROM information print
- Service test print
- Printing via USB connection
- Copying
- Direct printing from a digital

camera (PictBridge)

Absorber kit

After replacement:

1. Reset the ink absorber counter.

[See

3-3. Adjustment /

Settings, (6) Service mode

, for

details.]

- Ink absorber counter value

print (After the ink absorber
counter is reset, the counter
value is printed
automatically.)

Carriage unit

At replacement:

1. Before removal of the carriage

rail, mark the carriage rail
position.
[See

3-2. Special Notes on

Repair Servicing, (7) Carriage
unit removal

, for details.]

2. Apply grease to the sliding

portions of the carriage rail.
[See

3-3. Adjustment /

Settings, (3) Grease
application

, for details.]

3. Check the ink system function.

[See

3-3. Adjustment /

Settings, (6) Service mode

, for

details.]

4. Perform print head alignment in

the user mode.

- Service test print (Confirm ink

system function.)

Switch system unit

- The red screws securing the paper

feed motor are allowed to be
loosened only for paper feed
motor replacement. (DO NOT
loosen them in any other cases.)

At replacement:

1. Adjust the paper feed motor.

[See

3-3. Adjustment /

Settings, (1) Paper feed motor
adjustment

, for details.]

- EEPROM information print
- Service test print

Paper feed motor

Platen unit

After replacement:

1. Perform LF / Eject correction in

the service mode.
[See

3-3. Adjustment /

Settings, (6) Service mode

, for

details.]

- EEPROM information print
- Service test print

13 / 44

Содержание PIXMA MP620 series















































Результаты поиска

Содержание PIXMA MP620 series

Отзывы:

Похожие инструкции для PIXMA MP620 series

Бренды по названию

Популярные бренды

Canon PIXMA MP620 series, Руководство по обслуживанию

Результаты поиска

Содержание PIXMA MP620 series

Отзывы:

Похожие инструкции для PIXMA MP620 series

Бренды по названию

Популярные бренды