Canon PD-704 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 26

Canon PD-704 Скачать руководство пользователя страница 19

19

Non-Contact Displacement Sensor User’s Manual Rev 1.00

4-3-4.

Measurement distance adjustment tool

This tool allows you to visually find the best measurement distance.
- How to use the measurement distance adjustment tool
Insert the measurement distance adjustment tool to the main unit, and then secure it with the bundled M4 (L = 6)
screws.

Enter the trigger on the I/O or Non-Contact Displacement Sensor software.
One or two lines of light beam are irradiated on the target measurement object.
Two lines of light beam overlap on the best measurement distance and appear as one line.
Adjust the mounting height of the main unit or the height of the target measurement object so that two lines of light
beam will overlap.
The linear light matches the length measurement position, and can be used to align a thin measurement object.

When mounting is finished, turn off the length measurement trigger, and remove the measurement distance
adjustment tool.

Do not look into the light beam as it is very bright.
Also pay attention to light beam reflected on a metal, etc.

CAUTION

Main unit

Measurement distance
adjustment tool

Best measurement
distance

Light beam

«
...
17
18
19
20
21
...
»

Содержание PD-704



























Отзывы:

Нет отзывов