Canon iR5055, Руководство по обслуживанию

Страница: 570 / 646

Chapter 17
17-38
MODEL-SZ Use it to switchover the default magnification ratios and ADF original size detection.
0: AB (6R5E)
1: inch (5R4E)
2: A (3R3E)
3: AB/inch (6R5E)
1
FIX-TEMP Use it to select down sequence mode.
0: normal
1: st 10 deg C (default)
2: standard - 5 deg C
1
FUZZY Use it to turn on and off fuzzy control and to set the environment.
0: enable fuzzy control (default)
1: fix to low humidity environment mode (current level lower than standard)
2: fix to normal temperature/humidity mode
3: fix to high humidity mode (current level higher than standard)
1
CONFIG Use it to select multiple firmware items stored on the hard disk and switchover country, language, machine type, and paper size
configuration.
Procedure
XXYYZZ
XX: country (JP); YY: language (ja); ZZ (00): machine type; AA (00): paper size configuration. The indications will be in keeping
with the following: COPIER>DISPLAY>USER>LANGUAGE.
(The notations in parentheses indicate defaults. The country and language notations are for indication only.)
1) Select <CONFIG>.
2) Select the appropriate item to highlight, and press the +/- key.
3) See that each press on the +/- key changes the selections in sequence.
4) When you have made all selections, press the OK key.
5) Turn off and then on the main power switch.
1
TR_SP_C1 Use it to change the transfer/separation output settings when the right deck is used as the source of paper by way of providing a
remedial measure.
Setting
0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_C2 Use it to change the transfer/separation output setting when the left deck is used as the source of paper by way of providing a
remedial measure.
Settings
0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_C3 Use it to change the transfer/separation output setting when the cassette 3 is used as the source of paper by way of providing a
remedial measure.
Settings
0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_C4 Use it to change the transfer/separation output setting when the cassette 4 is used as the source of paper by way of providing a
remedial measure.
Settings
0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_MF Use it to change the transfer/separation output setting when the manual feed tray is used as the source of paper by way of providing
a remedial measure.
Settings
0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
TR_SP_DK Use it to change the transfer/separation output setting when the side paper deck is used as the source of paper by way of providing
a remedial measure.
Settings
0: normal (default); 1: separation fault; 2: double transfer; 3: transfer fault
1
W/SCNR Use it to indicate the presence/absence of a reader unit.
0: reader unit absent (printer model)
1: reader unit present (default)
When the presence of a reader unit is detected, the machine will automatically set it to '1'.
1
DFDST-L1 Use it to adjust the dust detection level for the ADF (sheet-to-sheet correction).
A higher setting will cause the machine to be more sensitive to finer particles of dust.
setting: 0 to 225
(Setting the item to '0' will disable the dust detection mechanism.)
1
DFDST-L2 Use it to adjust the dust detection level for the ADF (post-job detection).
A higher setting will cause the machine to detect finer particles of dust.
setting: 0 to 255
(Setting the item to '0' will disable the dust detection mechanism.)
1
ENVP-INT Use it to set the interval at which a log is collected for the machine inside temperature/humidity and fixing temperature.
COPIER>FUNCTION>MIS-P>ENV-PRT and
COPIER>DISPLAY>ENVRNT
setting
0 to 480 (default: 60; in min)
1
COPIER > OPTION > BODY
Sub-item Description Level