Canon imageRUNNER ADVANCE C7565i II Скачать руководство пользователя страница 22

Страница: 22 / 24

Procedure

Detail

Note

Time

Check to make sure
the Machine and
Accessories are level



Point:

1. The

Vertical Gaps

between the Machine and all

of the accessories should be

Even from Top to

Bottom.

2. If necessary, first make sure the machine is

level, then level each accessory starting with
the one closest to the machine then proceed
downstream.

Execute Drum, Roller
Wire and Feeder
Cleaning in User
Mode

Settings/Registration>Adjust/Maintenance>

Clean Wire and Clean Drum

Auto Color Mismatch
/ Auto Adjust
Gradation

Run COPIER/FUNCTION/MISC-P/SPIT-EX

Run COPIER/FUNCTION/INSTALL/TD-AD-4

Auto Correct Color Mismatch

Settings/Registration > Adjustment/Maintenance >

Adjust Image Quality•

> Auto Correct Color

Mismatch

4. Auto Adjust Gradation

Settings/Registration>Adjustment/Maintenance >
Adjust Image Quality•

> Auto Adjust Gradation



Point:

Perform SPIT-EX ; This will supply new toner
by ejecting the toner in the developing
assembly.

Perform TD-AD-4 to adjust the “toner to

        developer” ratio to 10% inside the developing
        assembly.
3.   Perform Auto Color Mismatch, then perform

Auto Adjust Gradation for all paper types.

4. If the machine has an imagePASS, perform

calibration for imagePASS after performing
Auto Adjust Gradation.

min

Adjust

7
min

Clean

Clean

Adjust

Mai

ntenanc

Proc

M21

Process (Aft

er)

C12

C13

iRADV C7580i/C7570i/C7565i Advance Maintenance Guide

Содержание imageRUNNER ADVANCE C7565i II

























Результаты поиска

Содержание imageRUNNER ADVANCE C7565i II

Отзывы:

Похожие инструкции для imageRUNNER ADVANCE C7565i II

Бренды по названию

Популярные бренды

Canon imageRUNNER ADVANCE C7565i II, Руководство по техническому обслуживанию

Результаты поиска

Содержание imageRUNNER ADVANCE C7565i II

Отзывы:

Похожие инструкции для imageRUNNER ADVANCE C7565i II

Бренды по названию

Популярные бренды