0
When the printer cannot be found on the network
If your printer cannot be found when connecting to
the network for the first time, setup an IP address
for the printer and then configure it on the printer.
When ink fills the system for the first time, after
printhead adjustment is finished, specify the IP
address on the printer's control panel.
• When ink fills the system for the first
time, do not operate the printer until
printhead adjustment is finished.
1
On the tab selection screen of the control
panel, press the
▲
and
▲
keys to select
(settings/adj. tab) and press
OK
.
678
Tot.Print Area(m2):
Maint.C Remain.: 80%
No Paper Loaded
OK:Setting/Adj. Menu
2
Use the ▲ and ▼ keys to select
Interface
Setup
and press
OK
.
3
Use the ▲ and ▼ keys to select
TCP/IP
and press
OK
.
4
Enter the IP address. Navigate through
the following menus using the ▲ and ▼
keys on the control panel.
. Select
IPv4
and press
OK
.
2. Select
IPv4 Settings
and press
OK
.
3. Select
IP Address
and press
OK
.
4. Enter the IP address.
MEMO
How to enter IP addresses
. Press the
▲
and
▲
keys to select a
field for inputting values.
2. Use the ▲ and ▼ keys to input values.
• Pressing ▲ increases the value by
one.
• Pressing ▼ decreases the value by
one.
• Holding down either the ▲ or ▼ keys
continually increases or decreases
the value.
3. Press
OK
once you have finished.
5
Press
Menu
.
6
On the registration confirmation message
that appears, select Yes using the ▲ and
▼ keys, and then press
OK
.
The IP address is set on the printer.
Next, restart installation of the printer
driver.
7
In the
Search Results
window, select
Specify the IP address of available
printers in the network
and click
Next
.
When the
IP Address Specifications
window appears, follow the instructions of
"When entering the printer's IP address
manually" in step 8 to on page 9 to
complete the installation of the software.
MEMO
• If the following screen appears, click
Retry
and select
Specify the IP
address of available printers in
the network
on the next screen that
appears.
Using DHCP
To use the DHCP server function to automatically
allocate an IP address to the printer, one of the
following settings needs to be configured. Check
with your network administrator for the settings
that match your system.
When used in an environment with a DNS
server
Configure the DNS dynamic update function in
the printer and register the printer DNS host name
with the DNS server.
When used in an environment without a DNS
server
Configure the DHCP server to always allocate the
same IP address to the printer.
This section describes how to turn on DNS
dynamic update from the control panel of the
printer.
MEMO
• The DNS dynamic update function can
also be configured using Remote UI.
Refer to "Configuring the Printer's TCP/
IP Network Settings With RemoteUI" in
the user guide for details.
1
Perform steps to 3 of the procedure in
"When the printer cannot be found on the
network" on page 0.
2
Select
IPv4
or
IPv6
using the ▲ and ▼
keys and then press
OK
.
3
Select
DNS Settings
using the ▲ and ▼
keys and then press
OK
.
4
Select
DNS Dync update
using the ▲
and ▼ keys and then press OK.
5
For IPv4
Select
On
using the ▲ and ▼ keys and
then press
OK
.
For IPv6
. When
Use the same host name and
domain name as IPv4?
is displayed,
select
Off
using the ▲ and ▼ keys and
then press
OK
.
2. Select
Statefull Addr
using the ▲ and
▼ keys and then press
OK
, and then
select
On
using the ▲ and ▼ keys and
then press
OK
.
3. Set
Stateless Addr
to
On
using the
same procedure as in Step 2.
