Canon imageFormula DR-6010C Скачать руководство пользователя

Страница: 84 / 142

Chapter 5

Troubleshooting

5-6

5-2 Uninstalling Software

If the ISIS/TWAIN driver, and “CapturePerfect 3.0” are not operating normally, follow the procedure

below to uninstall them.

Then, re-install the software from the DR-6010C setup disc.

(See “2-3 Installing the Software,” on

p. 2-4.)

IMPORTANT

Be sure to log on as an administrator when using Windows 2000 Professional or Windows XP.

Click the [Start] button

[Control Panel].

Note

For Windows XP, click the [Start] button

click [Control Panel].

The [Control Panel] window appears.

Click [Programs]

[Programs and Features].

Note

If you are using Windows XP, double-click the [Add or Remove Programs].

Содержание imageFormula DR-6010C















































































































































Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды

Canon imageFormula DR-6010C, Руководство пользователя

Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды