Canon imageFormula DR-6010C Скачать руководство пользователя

Страница: 55 / 142

Chapter 3

Basic Operation

3-25

On the [Other] tab of the ISIS driver properties, set the batch separation setting to

“Patchcode.”

From the application, perform scanning with batch separation enabled.

Note

If you are scanning with CapturePerfect, set the Type of batch separation setting to “Scan,

Continue Scanning” or “Skip, Continue Scanning.”

• If “Scan, Continue Scanning” is selected, the patchcode sheet image is also saved and

scanning continues.

• If “Skip, Continue Scanning” is selected and the PATCH T (FILE A) pattern is detected, the

patchcode sheet image is not saved and scanning continues.

IMPORTANT

Make sure to keep the patchcode sheets clean. In particular, the effective area for detecting

patterns should be kept clean. Also, do not fold them or allow them to become creased. If this

happens, the scanner will not be able to read them.

Содержание imageFormula DR-6010C















































































































































Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды

Canon imageFormula DR-6010C, Руководство пользователя

Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды