Canon imageFormula DR-6010C Скачать руководство пользователя

Страница: 61 / 142

Chapter 3

Basic Operation

3-31

• When scanning in the Long Document mode, if the document is placed on the scanner in a

skewed position, it may be damaged. Be careful to place the document so that it is not

skewed.

• When scanning with the Long Document mode, paper jam detection may react slowly,

resulting in damage to the document. Be careful to avoid paper jams.

• When scanning long documents, make sure to feed them one page at a time with the

bypass mode.

Long Document Mode Settings

Follow the procedure below to set the Long Document mode.

Use the following procedure to open the [CANON DR-6010C USB Properties] (or [CANON

DR-6010C SCSI Properties].)

1. Click [Start] - [Control Panel] to open the Control Panel.

Note

Under Windows 2000, click the [Start] button and select [Settings] - [Control Panel] to open

the Control Panel, then proceed to step 3.

2. Click [Hardware and Sound].

Note

Under Windows XP, click [Printers and Other Hardware].

Содержание imageFormula DR-6010C















































































































































Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды

Canon imageFormula DR-6010C, Руководство пользователя

Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды