Chapter 5
5-5
F-5-2
3) Turn on the host machine power.
4) Press SW103 on the finisher controller PCB.
• When SW103 is pressed, the swing guide opens and the alignment plate moves to prescribed position.
5) Place a sheet of paper between the alignment plates, push it against the stopper, and push the rear edge of the paper
against the rear alignment plate.
• If the gap between the front alignment plate and front edge of the paper is 1 mm or greater, end staple position
adjustment and repeat staple position adjustment after completing alignment plate adjustment.
6) Press SW103 on the finisher controller PCB once to staple. However, remove the
stapled paper manually to
verify the staple position because it is not ejected.
7) Press SW103 on the finisher controller PCB once.
8) If the staple position is correct, insert a sheet of paper between the aligning plates and
push it against the stopper,
push the far end edge of the paper to the rear aligning plate,
and press SW103 once (stapling action/store
adjustment value) and proceed to step 11).
9) To adjust the staple position, press SW101 or SW102 on the finisher controller PCB and
adjust the staple
position.
• When SW101 is pressed, staple position moves 0.49 mm forward.
• When SW102 is pressed, staple position moves 0.49 mm backward.
10) Repeat steps 5) and 6) and check that the staple position is adjusted correctly.
11) Turn off all bits of SW104 on the finisher controller PCB.
12) Turn off the power of the host machine and install the rear cover of the finisher unit.
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
A4/rear stitch
A4/front stitch
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
A4R/rear stitch
A4R/front stitch
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
LTR/rear stitch
LTR/front stitch
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
LTRR/rear stitch
LTRR/front stitch
Содержание Finisher-R1
