background image

Parts Description 

 
1. 

Reel 

 

This is used to spool the cable, available in lengths ranging from 150 to 400 feet. 

 
2. 

Boom 

 

This is used to extend the weight out from the body of the downrigger and has a pulley fixed 
to its end. Boom lengths range from 24 to 53 inches. 

 
3. 

Swivel Head 

 

This relays the cable at the end of the boom to lower the weight. 

 
4. 

Weight 

 

This is used to maintain the depth at which you want to fish. Sizes of weights range from 4 to 
20 lbs. 

 
5. 

Cable 

 

This connects to the weight. Cable material is 150 lb. test stainless steel cable. 

 
6. 

Depth Meter 

 

This determines how much cable you have run out, enabling you to choose your trolling 
depth. 

 
7. 

Mounting Base

  This attaches to the boat, enabling you to place the downrigger where you choose. 

 
8. 

Rod Holder

 

This holds your fishing rods while trolling and may also be used for storing rods. 

Introduction to Controlled Depth Fishing 

 

Undoubtedly there are many fishermen 

familiar with the methods and use of controlled 
depth fishing. During the mid 1960's the state of 
Michigan introduced Pacific salmon into the Great 
lakes in an attempt to revitalize its sport fishing 
industry. From this successful transplant, new 
fishing techniques and equipment were 
developed. One such method was controlled 
depth fishing which enabled fishermen to place a 
lure at a desired depth by utilizing downriggers.  
 

Because of the varying factors (water 

temperature, thermocline, weather, tides, time of 
day, or time of year) it is necessary for successful 
fishing to maintain specific water depths that 
coincide with fish movements and feeding 
patterns. 

 

One essential feature of the downrigger is 

the depth meter or gauge that indicates lure 
depth. This allows the angler to control as well 
as return to specific depths where fish have 
been caught.  
 

Due to the success of controlled depth 

fishing, downriggers are now being used 
throughout the world to catch a wide variety of 
species in both fresh and salt water. Whether 
fishing for blues off Rhode Island, walleyes in 
Lake Erie, sailfish off the coast of Florida, or 
stripers in Tennessee, the use of downriggers 
will make your fishing more successful and more 
enjoyable. 

Attach Line Release to 
Rear Hook on Weight 

In
troduction

 to d

o

w
n

rig

g

ers 

Содержание MAG 10HS

















Отзывы: