background image

5

Do not spray aerosols in the vicinity of this appliance while it is in

operation.
Do not modify this appliance.

8.  If removed, the glass window must be put back onto the unit prior to

operating the heater.

9. Installation and repairs should be performed by a licensed service

person only, refer to back of brochure for service number.

10. The appliance should be inspected prior to use, with regular inspec-

tions (annually) to be made by a licensed service person. It is important

that circulating air passageways of the appliance be kept clean, dirt

and lint free, for a safe and efficient operation of the heater.

11. On first lighting your heater a smell may occur due to its new condi-

tion. This is quite normal and will disappear after a few hours use at

the maximum control position.

12. Testing the effectiveness of the flue.

Before testing the flue confirm air vents are unobstructed. If an exhaust

fan or other heating appliances are present switch them on. This is to

test that there is no interaction between the CANNON heater and

other appliances.

Refer AS5601.

For ‘air movement not to affect appliance’ see clause 5.3.1.

For ‘air supply to appliance’ see clause 5.4.1.

For ‘ventilation requirements’ see clause 5.4.3.

Important:

When this heater is operating the mesh guard/glass front is hot.
The mesh guard, or glass front, fitted to the heater conforms to Austral-

ian Standards  requirements.
The guard is fitted to this appliance to reduce the risk of fire or injury

from burns and no part of it should be permanently removed.
For protection of young children or the infirm, a secondary guard is

required.
This heater is not intended for use in a marine environment.

Standards

This appliance meets the following standards:

Standards Australia:

AS/NZS 3100

AS 5601

AS 4553:2008

20

Wiring diagram

For service to this appliance

For service to this appliance or spare parts contact the CANNON distributor:

Sampford IXL

52-70 Sparks Avenue

Fairfield, Vic, 3078

Phone: 1300 727 421

Fax:

1300 727 425

email: service @ sampfordixl.com.au

Data label

Содержание FITZFS-SDSEB-NG

























Отзывы: