Cannon CT-500 Скачать руководство пользователя | Manualshive

Страница: 20 / 49

background image

12

CT-500 Instruction Manual

5.

Attach the top cover, making sure all cords pass through the rear opening and down the vertical
shaft. Secure the front cover first. Use the two longer screws with toothed washers from the
Accessories Kit to secure the housing to the sides of the vertical shaft.

CT-600 TE Cooler and Motor-Stirrer Installation

This section of the installation procedure is for the CT-600 bath only.

The CT-600 is shipped with the top housing sections installed, but with the motor-stirrer and TE
cooling unit packaged separately. To complete CT- 600 installation, remove the housing sections,
install the motor-stirrer and TE cooling unit, and reassemble the housing. Follow the procedure
below to install these components.

1.

Remove the two screws securing the rear housing to the bath chassis as shown in Figure 5. Set
the screws aside.

Figure 5: Remove Top Rear Housing

2.

Loosen but DO NOT REMOVE the two top screws securing the front housing as shown in Figure
6. This will provide play for removal of the rear housing.

Figure 6: Remove Top Rear Housing

3.

Remove the rear housing by sliding it backward away from the bath.

4.

Remove the screws securing the front housing to the bath chassis.

5.

Remove the front housing.

«
...
18
19
20
21
22
...
»

Содержание CT-500


















































Отзывы:

Нет отзывов

Похожие инструкции для CT-500

Бренд: Nitecore Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: OAKWORKS Страницы: 24

Бренд: Yamaha Страницы: 29

Бренд: Feniex Страницы: 5

Бренд: EFX Страницы: 2

Бренд: Xtricity Страницы: 4

Бренд: Teac Страницы: 2

XMLT-24ELED-200CA8-1

Бренд: DS Produkte Страницы: 28

IMPULSE 2 IT8026 Glute Master

Бренд: BM FITNESS Страницы: 18

Бренд: American DJ Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды