When the layer of frost present in the freezer compartment exceeds
3mm, it is recommended to proceed with the defrosting as it increases
energy consumption.
1)
To bring the product in to stand by status see switching on and off
display.
2) Disconnect the power cord.
3) Remove the frozen food and temporarily place them in a cool
place.
4) Leave the freezer door open to speed defrosting.
5) Collect the water on the bottom of the product.
6) Dry the freezer.
7)
8) Wait a moment and reintroduce the frozen foods.
WARNING:
Absolutely avoid the use of open flames or electrical appliances, such as
heaters, steam cleaners, candles, oil lamps and the like to accelerate the
defrosting phase.
Do not scrape with a knife or sharp object to remove frost or ice present.
These can damage the refrigerant circuit, the leakage of which can cause
a fire or damage your eyes.
Reconnect the power cord and set the desired values
.
LED lighting (Where present)
If the product is equipped with
LED
lights, please contact the Technical
Assistance Service in case of replacement.
Compared to traditional light bulbs, the
LED
s last longer and are
environmentally friendly.
NOTICE:
• Before each operation, remove the refrigerator plug from the power
socket to prevent electric shocks.
• Do not pour water directly on the outside or inside of the refrigerator
itself. This could lead to oxidation and damaging of the electrical
insulation.
IMPORTANT:
To prevent cracking of the inside surfaces and plastic parts, follow
these suggestions:
• Wipe away any food oils adhered to plastic components.
• The internal parts, gaskets and external parts can be cleaned with a cloth
with warm water and baking soda or a neutral soap. Do not use solvents,
ammonia, bleach or abrasives.
• Remove the accessories, for example, the shelves, from the refrigerator
and from the door. Wash in hot soapy water. Rinse and thoroughly dry.
• The back of the appliance tends to accumulate dust which can be
eliminated with the use of a vacuum cleaner, after having switched off and
disconnected the appliance from the electrical outlet. This provides greater
energy efficiency.
For better energy savings, we suggest:
• Installing the appliance away from heat sources and not exposed to
direct sunlight and in a well ventilated room.
• Avoid putting hot food into the refrigerator to avoid increasing the
internal temperature and therefore causing continuous functioning of
the compressor.
• Do not excessively stuff foods so as to ensure proper air circulation.
• Defrost the appliance in case there is ice (see DEFROSTING) to
facilitate the transfer of cold.
• ln case of absence of electrical energy, it is advisable to keep the
refrigerator door closed.
• Open or keep the doors of the appliance open as little as possible
• Avoid adjusting the thermostat to temperatures too cold.
• Remove dust present on the rear of the appliance (see CLEANING).
Products with display
See Turn ON / OFF Display
For products with a NO FROST freezer compartment, activate the
SUPER FREEZING function 8 hours before introducing the foods.
For the other products, activate the SUPER FREEZING function at the
time of introduction of the foods.
DEFROSTING
Defrosting the refrigerator compartment
During normal functioning, the refrigerator is automatically defrosted.
There is no need to dry the drops of water present on the rear wall or
to eliminate the frost (depending on functioning).
The water is conveyed to the rear part through the drain hole found
there and the heat of the compressor causes it to evaporate.
• Keep the drainage pipe (
fi
g. 9) clean in the refrigerator compartment
to keep it free of water.
Defrosting the freezer compartment
(static products without NO-FROST technology)
Defrosting the freezer compartment
(NO-FROST products)
Defrosting is automatic.
MAINTENANCE AND CLEANING
ENERGY SAVINGS
Fig.9
Lighting
Cleaning
EN 15
Содержание 41041090
Страница 2: ......
Страница 33: ...09 2014 41041090 Rev_0...
