background image

129 

 

PWC JETROLL SYSTEM ANCHORING GUIDELINES 

 

The  following  configurations  are  showcased  to  help  determine  the  best  scenario  for  each  situation.  The  number  of  factors  that 
influence the exact suggested layout is numerous, so the following proposed layouts must not be taken integrally. Modifications and 
altering of these are highly probable. Please contact a Candock representative to gather clarification and validation on the below 
configurations.  

The  below  section  is  segmented  as  per  our  anchoring  accessories/techniques  categories.  Note  that  combinations  of  multiple 
techniques may or may not apply, and some alterations of the below accessories/techniques may also be involved in the process. The 
below list aims at covering as many of the possible scenarios. If the Jetroll system is secured against another floating or fixed structure 
(another Candock system, a regular floating dock, a fixed dock, or seawall), this “other” structure must be adequately anchored or 
fixed in place to withstand the torque that the addition of the Jetroll will apply. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STAND ALONE 

ANCHORING WITH  

PILES & PVC 

SLEEVES

 

ANCHORING WITH  

SWIVEL ANCHOR 

CHANNELS 

 

ANCHORING WITH 

ANCHORING 

STRUTS 

 

(LENGTH 5’ MAX)

 

CONNECTED TO A 

CANDOCK WITH 

(4X) EXTENDED 

CONNECTING PINS + 

(12x) SPACERS 

 

ANCHORING WITH  

2 7/8’’ STEEL PILES + 

PVC SLEEVES AND 

UPPER PILE SECTION 

FASTENING 

ACCESSORIES

 

CANDOCK 

FIXED 

FLOATING 

FIXED 

Содержание JETROLL












Отзывы: