Canary MultiMux Скачать руководство пользователя страница 3

Страница: 3 / 14

Section 1 - Introduction

1.1 Overview

The MultiMux expands the number of instruments that may be read by the CR10 or CR10X in increments
of 16, 32 or 48, depending on the model purchased and the type of sensor being read. In addition the
MultiMux provides integral lightning protection by utilizing plasma surge arrestors (optional). The MultiMux
may be purchased installed in a NEMA 4X fiberglass/polyester enclosure or as a board assembly for
users supplying their own packaging.

The complete list of features and ordering options is detailed on the MultiMux Ordering Guide available
from our web site or by contacting Canary Systems directly.

The MultiMux consists of two printed circuit boards (PCB

’

s), one for making the instrument connections

(the terminal board) and the second, installed on the back of the terminal board (the switch board), for
switching the instrument leads. The MultiMux utilizes advanced high-reliability components such as
terminal blocks from Phoenix Contact (

http://www.phoenixcontact.com

), relays from Aromat

corporation (

http://www.aromat.com

) and a microcontroller from Microchip Devices

(

http://www.microchip.com

) to help insure years of reliable and trouble-free operation. The use of low

contact resistance relays means almost universal instrument support, a high degree of lightning
protection and virtually infinite channel isolation.

Warranty is applicable for 2 years from date of shipment. Warranty does not cover failure by misuse or by
nature including lightning, flood, or other catastrophe. Should you encounter problems with your MultiMux
see the troubleshooting flowchart in section 3.

A top view and description of the MultiMux terminal board is shown below.

1H2

1L2

2H3

2L3

3H3

3L3

4H3

4L3

SHIELD

12V

16/32/48 CHANNEL TERMINAL BOARD

1H1

1L1

2H1

2L1

3H1

3L1

4H1

4L1

SHIELD

CLK

1H3

1L3

2H2

2L2

SHIELD

3H2

3L2

4H2

4L2

SHIELD

5H2

5L2

6H3

6L3

7H3

7L3

8H3

8L3

SHIELD

5H1

5L1

6H1

6L1

7H1

7L1

8H1

8L1

SHIELD

5H3

5L3

6H2

6L2

SHIELD

7H2

7L2

8H2

8L2

SHIELD

13H2

13L2

12H3

12L3

11H3

11L3

9H3

9L3

SHIELD

13H1

13L1

12H1

12L1

10H1

10L1

9H1

9L1

SHIELD

13H3

13L3

12H2

12L2

SHIELD

10H2

11L2

9H2

9L2

SHIELD

16H2

16L2

15H3

15L3

14H3

14L3

13H3

13L3

SHIELD

16H1

16L1

15H1

15L1

14H1

14L1

13H1

13L1

SHIELD

16H3

16L3

15H2

15L2

SHIELD

14H2

14L2

13H2

13L2

SHIELD

TB1

TB2

TB3

TB4

TB5

TB6

TB7

TB8

TB9

TB10

TB11

TB12

TB13

TB14

TB15

TB16

Canary Systems, Inc.

SA37

SA38

SA39

SG13

SA40

SA41

SA42

SG14

SA43

SA44

SA45

SG15

SA46

SA47

SA48

SG16

SA1

SA2

SA3

SG1

SA4

SA5

SA6

SG2

SA7

SA8

SA9

SG3

SA10

SA11

SA12

SG4

SA13

SA14

SA15

SG5

SA16

SA17

SA18

SG6

SA19

SA20

SA21

SG7

SA22

SA23

SA24

SG8

SA25

SA26

SA27

SG9

SA28

SA29

SA30

SG10

SA31

SA32

SA33

SG11

SA34

SA35

SA36

SG12

Datalogger Connection

TB17

Manual Switch Header Sockets (optional)

Interboard Connectors

Screw Terminal Blocks (16 places)

Surge Arre stors (op tional)

Datalogger Connection

Earth Ground Connection (2 place s)

Mounting Hole (4 places)

8.813"

223.8mm

10.750"

273.05mm

Содержание MultiMux















Результаты поиска

Содержание MultiMux

Отзывы:

Бренды по названию

Популярные бренды

Canary MultiMux, Руководство пользователя

Результаты поиска

Содержание MultiMux

Отзывы:

Бренды по названию

Популярные бренды