CAMSO 24D17C Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 48

CAMSO 24D17C Скачать руководство пользователя страница 35

CBP-436(2017) Operation and Maintenance Manual-CTS Tractors

Camso | 12-17 | 35

4. Remove oil plug at top of main support and fill

with oil through the drain plug until oil level is

between the “L” and “F” marks on the site

glass,

For 24D17C and 24D18C models,

refill with 1.25 quarts (1.2 liters)

For 30/36D23MC and 30/36D22MC models,

refill with 2.3 quarts (2.2 liters)

5. Once filled, reinstall the oil plug.

WARNING

Lubricants should not to be poured in the environment. Collect them in

suitable containers and deliver to licensed companies for waste

disposal in accordance with the present law in force.

Avoid any contact of the lubricant with the rubber parts. If oil is spilled

onto the track, clean oil from track surface with dry towel. Do not use

cleaning solvents or diesel fuel to clean oil from track surface as track

damage may occur.

WARNING

Use only high quality lubricants with the same characteristics shown in

“Lubricant table” section, stored in sealed containers according to

manufacturer specifications.

«
...
33
34
35
36
37
...
»

Содержание 24D17C

















































Отзывы:

Нет отзывов