CAMSO 24D17C Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 48

CAMSO 24D17C Скачать руководство пользователя страница 21

CBP-436(2017) Operation and Maintenance Manual-CTS Tractors

Camso | 12-17 | 21

5.4 Daily maintenance or every 10 working hours

1. Track system inspection. Walk around the machine inspecting each undercarriage and

oscillation limiting brackets. Identifying and resolving issues early are key to improving

track system life and decreased operating expenses. See “Track System Inspection” in

the Routine maintenance section for more information.

2. Check the track tension by verifying the circuit pressure measured by the gauge being

1000 psi ± 175 psi (70 ± 12 bar). If track tension pressure is not within the desired range,

refer to “Track tension adjustment” in “Routine maintenance” section.

WARNING

Should the rubber track be not tensioned correctly or not tensioned at all:

x

Braking performance will be diminished

x

The ability to transfer power to the ground will be decreased

x

Serious damage can occur to the rubber track in a short time,

especially damage to the drive lugs.

3. Check the main support oil level. Oil level should be between the full and add mark on the

site glass.

Oil Level Site

Glass

«
...
19
20
21
22
23
...
»

Содержание 24D17C

















































Отзывы:

Нет отзывов