manualshive.com logo in svg

CAMSO 24D17C, Руководство по эксплуатации и обслуживанию, Страница: 14 / 48

Поделиться
Скачать
CAMSO 24D17C Скачать руководство пользователя страница 14

CBP-436(2017) Operation and Maintenance Manual-CTS Tractors

Camso |  12-17 | 14

3.6 Weight Limitations

Camso track conversion systems are limited to operating weights as listed in the table below. Do 

not exceed these weight limitations or track system damage or component failure may result.

Series

Max Operating Weight

30/36D23MC

50,000 lbs (22,700 kg)

30/36D22MC

50,000 lbs (22,700 kg)

24D17C

31,000 lbs (14,000 kg)

24D18C

31,000 lbs (14,000 kg)

3.7 Maximum Speeds

Due to the differences from the available tire sizes and the size of the drive wheel on the track 

system, a speed reduction of up to 40% can be expected. Depending on tractor transmission 

type, a slight increase in speed may be obtained by adjusting the tire size to the smallest 

available in the tractor settings.

Maximum Tractor 

Speed on Tires

Approximate Maximum Speed 

with CTS 

26 MPH 

(41 kph)

14.5 – 16 MPH

(23 – 26 kph)

31 MPH

(50 kph)

17 - 19 MPH

(27 – 30 kph)

3.8 Transport Limitations

Camso track systems are designed for field use and field operational speeds. High speed 

transport, is not recommended, and may result in track damage due to heat. If extended 

transport is required between operating locations, the following speed and duration limits should 

be observed:

Transport Speed 

(Maximum)

Transport Duration 

(Maximum)

17 - 19 MPH 

(27 - 30 kph)

45 min.

14 - 16 MPH

(23 - 26 kph)

60 min

If additional distances are required, a 30 minute cool down period is recommended before 

transport is resumed. Absolute speed and duration levels may vary, depending on system type 

and ambient conditions, but as listed, are appropriate limitations to avoid system heat buildup 

that could cause reduction in track life.

Содержание 24D17C

















































Отзывы:

Нет отзывов