Campingaz ATTITUDE 2go, Инструкция по эксплуатации

Страница: 9 / 13

GB
NOTE: Unless otherwise specified, following generic terms “appliance / unit / product / equipment / device” appeared in this
instruction manual all refer to the product “Attitude 2go”.
The product shown in this manual may look different from yours. It is for illustration purpose only.
y
Please read the instructions carefully before use.
y
Use outdoors only.
y
It is best to wear gloves to assemble the product.
y
Do not use charcoal.
y
Do not use an adjustable low pressure regulator. Only use fixed regulators that comply with relevant European
Standards.
y
To ensure safe operation of your device, never use two full griddles side by side.
y
Regularly clean the parts at the frame bottom to avoid risk of inflammation from fat drippings.
Follow these instructions carefully to avoid serious damage to your barbecue.
This product is designed for a normal private use, not intended for commercial purposes.
INSTRUCTIONS FOR USE
A. GAS CATEGORY & PRESSURE
Injector mark: 75
Heat output: 2.4 kW
Mass flow: 175 g/h (G30) / 172g/h (G31)
Cat I3+ (28-30 / 37)
Gas and pressure: Butane (G30) 28-30 mbar / Propane (G31)
37 mbar
B. FOR YOUR SAFETY
y
Do not store or use petrol and other flammable liquids or
vapours in the vicinity of this appliance. This device must
be kept away from inflammable materials when it is in use.
If you smell gas:
1.
Close the valve of the cylinder.
2. Extinguish all naked flames.
3. Open the lid.
4.
If the smell continues, see “
F. Checking for gas leaks
” or
immediately seek advice from your local retailer.
y
Do not leave your appliance unattended while it is working.
y
Parts which are protected by the manufacturer or the
manufacturer’s representative must not be manipulated by
the user.
y
Close the gas container after use.
C. LOCATION
y
This appliance must only be used outdoors.
y
CAUTION : accessible parts may get very hot. Keep young
children away.
y
There should be no combustible materials within a radius of
approximately 60 cm around the appliance.
y
Do not move the appliance when alight.
y
The appliance should be operated on a level surface.
y
Estimated air offtake is 2 m
3
/kW/h.
D. GAS CYLINDER
This appliance has been adjusted to operate from 3 to 15 kg
butane/propane cylinders with an appropriate low pressure
regulator: butane 28 mbar / propane 37 mbar.
Always connect or replace the cylinder in a well-ventilated
area, never in the presence of a flame, spark or heat source.
E. HOSE (FIG 1-2 & 3)
The appliance can be used with 2 types of hoses:
a) Hose for fitting onto ringed end pieces on the appliance and
regulator, secured by clamps (compliant with XP D 36-110
standard). Recommended length: 1.25 m.
b) Hose (compliant with XP D 36-112 or NF D 36-112 standard)
fitted with a G 1/2 threaded nut for screwing onto the
device and an M 20x1.5 threaded nut for screwing onto the
regulator, recommended length 1.25 m.
The appliance has a G 1/2 threaded connection for gas
flow supplied with the fitted NF ringed end piece and seal.
1) Using the device with a XP D 36-110 hose: (Fig. 2A)
- fit the hose tightly onto the ringed end piece of the appliance
and the regulator (Fig. 2C).
- slip the hose clamps behind the first 2 bosses of the end
pieces and tighten them until the clamp head breaks (Fig.
2C).
- Sealing is verified according to the instructions in paragraph f).
2) Using the appliance with XP D 36-112 or NF D 36-112
hose, G 1/2 and M 20x1.5 nuts: (Fig. 2B)
- Unscrew and remove the NF ringed end piece to detach the
G1/2 inlet connection.
- Remove seal.
- Screw the hose’s G 1/2 threaded nut to the appliance’s gas
connection, and the M20x1.5 threaded nut to the regulator
outlet connection, following the instructions supplied with the
hose (Fig. 2D) .
- Use 2 wrenches to tighten the hose on the gas connection
end piece of the appliance:
• A 14-wrench to secure the appliance’s inlet connection.
• An adjustable wrench to tighten the hose nut.
- Use a wrench to secure the outlet connection on the
regulator.
- Sealing is verified according to the instructions in paragraph f).
Do not pull on the hose or twist it. Keep it away from hot parts.
Check that the hose is in an appropriate position, without any
twisting or pulling and without being in contact with the hot
walls of the appliance (Fig3A & 3B).
It needs to be changed once it expires, according to the expiry
date written on the hose or, in any case, if it is damaged or
cracked.
F. LID
Handle the lid carefully, especially during operation. Do not
lean over the base.
G. CHECKING FOR GAS LEAKS
Important: never use a naked flame to check for gas leaks.
1. Work outside, away from all sources of ignition. Do not
smoke.
2. Make sure the control knob is in the “OFF” position ( O )
3. Fit the regulator onto the gas cylinder in accordance with
its instructions.
4. Connect the flexible hose to the regulator as described in
section D .
8