manualshive.com logo in svg

Campbell TGT1, Руководство оператора

Поделиться
Скачать
Campbell TGT1 Скачать руководство пользователя страница 59

I-1

Appendix I.  Changing the 21X's RAM or
PROM Chips

The 21X has 8 sockets for memory chips.  Five sockets hold 8K Random Access Memory
(RAM) chips and three hold Programmable Read Only Memory (PROM) chips.  Older
21Xs may have two PROM chips and as few as two RAM chips.

I.1  Disassembly of 21X

1.

Turn power off, remove the two Phillips head screws located near the
edges of the front panel of the micrologger.  Carefully lift the micrologger
up and away from the battery pack and disconnect the plastic power
connector.

2.

Lay the micrologger face down on a padded surface. Remove the four
Phillips head screws from the corners of the aluminum back plate. Lift the
back plate up and away to expose the 21X CPU board.  Figure I-1 shows
the CPU card; the memory chips are in the lower right hand corner.  The
locations numbered 1-5 hold RAM chips.  Locations 8, 7, and 6 hold
PROM chips.

FIGURE I-1.  Memory Sockets on CPU Card

Содержание TGT1

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды