manualshive.com logo in svg

Campbell TGT1, Руководство оператора

Поделиться
Скачать
Campbell TGT1 Скачать руководство пользователя страница 49

F-1

Appendix F.  Data Dump Datalogger
Program

F.1  Introduction

The data dump program inserts 20 data points (60 bytes) into the transmitter's
random buffer when user FLAG 1 is manually toggled HIGH.  The buffer is
cleared when the user FLAG 2 is set HIGH.

F.2  Toggling User FLAG 1 HIGH

You start by typing in *6AD to enter the FLAG Status Mode.  [00:00:00:00] is
displayed, indicating user FLAGS 1 through 8 are set low.  To toggle user
FLAG 1 HIGH, type 1.  After the display shows [10:00:00:00], type *0.  When
the data points are in the buffer, [00:00:00:00] is displayed.

If the display shows [00:00:00:00] before *0 is typed, the data dump failed.  To
try again, type a 1 and a *0.  Twenty seconds after the display shows LOG1,
type *6AD.  When [00:00:00:00] is displayed, the data points are in the buffer.
The FLAG Status Mode is exited by setting the scan rate to 0 (*1A0A) then
typing in *0.

F.3  Checking the Buffer

Check the buffer for the 20 data points (60 bytes) with *#60 commands 7 and 5
(see Section 8.3).  If the display shows a number other than 60, the data dump
failed.  You must then reset the scan rate to 10 and return to the Flag status
mode to set user FLAG 1 HIGH (see Section F.2).

F.4  Test Transmission

The antenna must be connected before the test or the
transmitter will be damaged.

To cause the TGT1 to transmit, use *#60 command 8.  The transmission will last
less than 5 seconds.  To verify transmission occurred, check forward and
reflected power (*#60 command 3).  The TGT-1 will not perform a test
transmission more often than once each minute.

F.5  Toggling User FLAG 2 HIGH

After the test transmission, the random buffer 

MUST BE

 cleared or the data

will be randomly transmitted throughout the transmission interval.  The buffer
is cleared by setting the scan rate to 10 and typing *6AD2 which sets user
FLAG 2 HIGH.  After the display shows [01:00:00:00], type in *0.  If
[00:00:00:00] is shown before *0 is typed, you must type in a 2 and a *0.

CAUTION

Содержание TGT1

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды