manualshive.com logo in svg

Campbell TGT1, Руководство оператора

Поделиться
Скачать
Campbell TGT1 Скачать руководство пользователя страница 13

TGT1 GOES Transmitter

3

4.  Required Equipment

4.1  Computer Base Station

The equipment required at the computer base station is listed below.

•

 

Phone modem with MNP level 4 error correction.  (Most commercially
available Hayes-compatible modems contain this error-checking protocol.
Check the operator's manual for your modem).

•

 

Computer with user-supplied commu-nication software (e.g., Procomm
Plus, Crosstalk).

4.2  Field Station

The field stations equipment is illustrated in Figures 4-1 and 4-2.  The required
equipment is listed below.

•

 

TGT1 satellite transmitter (includes the SC925G communication/power
cable).  If required, the datalogger's PROM is ordered with the transmitter.

•

 

Datalogger (CR23X, CR10X, CR500, CR10, or 21X).  A CR10KD
keyboard/display is required when using a CR10X, CR10, or CR500.  The
CR10 and 21X require a special PROM.  When using a 21X with both a
TGT1 and a storage module (SM192, SM716, or CSM1), hardware and
datalogger programming modifications are required.  Contact a Campbell
Scientific applications engineer for more information.

•

 

RHCP Yagi antenna, mounting bracket (CSI model 12261), and COAX
NM-L cable.

•

 

Campbell's ENC SAT enclosure.  The ENC SAT includes a water-tight
compression fitting for the antenna, 6 water-tight compression fittings for
the sensors and the solar panel, a 12 AHr or 24 AHr (optional) sealed
rechargeable battery, a Campbell's CH12R regulator, and an MSX10 solar
panel.

•

 

A 6832 filter is also required when measuring sensor(s) requiring
equalization with the atmosphere (e.g., vented pressure transducers,
barometers).  This filter fits into one of the ENC SAT compression fittings
to allow pressure equalization between the inside and outside of the
enclosure.  The filter retards the entry of water vapor into the enclosure
protecting the transmitter and measurement electronics.

Содержание TGT1

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды