Campbell SnowVUE 10 Скачать руководство пользователя страница 12

Страница: 12 / 33

CAUTION:
The SnowVUE 10 calculates distance readings using the
speed of sound at 0 °C (331.4 m/s). If the temperature
compensation formula is not applied or manually
specified using the

XWT!

command, the distance values

will not be accurate for temperatures other than 0 °C.

Resolution:

0.1 mm

Required beam angle clearance:

30°

Operating temperature range:

–45 to 50 °C

Sensor connector type:

Maximum cable length:

Cable type:

Chassis type:

Sensor length:

Sensor diameter:

Sensor weight without cable:

Cable weight (15 ft):

IP rating

Electrical housing:

Transducer:

Compliance:

M12,

5-pole,

A-coded,

connector

(197

ft)

3-conductor,

polyurethane

sheathed,

screened

cable,

4.8

(0.19

in)

nominal

diameter

Corrosion-resistant,

type

III

anodized

alumin

9.9

(3.9

in)

7.6

(3.0

in)

293

(10.3

oz)

250

(8.2

oz)

IP67

IP64

This

device

complies

with

Part

the

USA

Federal

Communications

Commission

(FCC)

Rules.

Operation

the

USA

subject

the

following

two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired
operation.

Compliance documents:

View

www.campbellsci.

/snowvue10

SnowVUE 10 Sonic Ranging Sensor

Содержание SnowVUE 10

































Результаты поиска

Содержание SnowVUE 10

Отзывы:

Бренды по названию

Популярные бренды

Campbell SnowVUE 10, Руководство по эксплуатации продукта

Результаты поиска

Содержание SnowVUE 10

Отзывы:

Бренды по названию

Популярные бренды