background image

SC105 CS I/O to RS-232 Interface 

RS-232 Baud Rates:

 

The SC105 will support the following baud 
rates: 1200, 9600, 19200, 38400, 57600, and 
115200 

RS-232 Parity and Data 

The SC105 supports the following: 
 

Parity:

 

Even, Odd, None 

 

Data Bits:

 7, 

CS I/O Port Modes:

 

CSDC, SDC, ME, 

Addressed Print Device

 for 

P96 output 

Electrical:

 

The SC105 uses power from the +5 V line on 
the 9-pin interface connected to the datalogger 

Current 

 

Standby:

 0.16 

mA 

 

Communicating:

 

1 to 4 mA 

 

 

Additional current (up to 8 mA) from the 5 V 
supply may be used by the RS-232 device 
connected to the SC105 

Physical 

 

Height:

 

2.3 cm (0.9 in) 

 

Width:

 

4.1 cm (1.6 in) 

 

Length:

 

8.9 cm (3.5 in) 

 

Weight:

 

45.4 g (1.6 oz) 

Environmental 

 

Temperature:

 

–25° to +50°C 

 

Humidity:

 

up to 95% non-condensing 

3.  Set-up Menu 

The SC105 has a built-in set-up menu for configuring communication mode, 
CS I/O port configuration, RS-232 port configuration, and other parameters.  
The Set-up Menu is shown in FIGURE 3-1.  It is accessed by connecting the 
SC105’s RS-232 port to a PC with the included null modem cable.  The SC105 
also needs to have power.  Usually, the SC105 is powered by connecting the 
SC105’s CS I/O port to the CS I/O port of a datalogger.   

With the null modem connection to the PC, typically Campbell Scientific’s 

Device Configuration Utility

 (

DevConfig

) is used, but a terminal program such 

as 

HyperTerminal

TM

 or 

Procomm

TM

 (always 9600 baud, 8-N-1) can also be 

used.  Press the 

Program

 button on the SC105 for one second to access the 

Set-up Menu.  Changed settings are saved in flash memory by selecting 

Apply

 

in DevConfig or menu item 

4

 if using HyperTerminal or Procomm.  If left idle, 

the Set-up Menu will time out 60 seconds after the last received character and 
exit without saving any parameter changes with the message “Set-up Timeout.”  
A datalogger can remain connected to the CS I/O port (to provide power to 
SC105) while setting SC105 parameters on the RS-232 port, although CS I/O 
communications would be inactive until exiting the Set-up Menu. 

Содержание SC105 CS



















Отзывы: