Campbell OBS501 Скачать руководство пользователя

Страница: 7 / 66

Table of Contents

PDF viewers: These page numbers refer to the printed version of this document. Use the
PDF reader bookmarks tab for links to specific sections.

Introduction ................................................................ 1

Precautions ................................................................ 1

Initial Inspection ......................................................... 2

3.1

Ships With ............................................................................................ 2

QuickStart ................................................................... 3

Overview ..................................................................... 5

5.1

Applications ......................................................................................... 5

5.2

Backscatter and Sidescatter Sensors .................................................... 5

5.3

ClearSensor

Antifouling Method ....................................................... 6

5.4

Comparison of OBS500 and OBS501 .................................................. 6

Specifications ............................................................. 6

Installation .................................................................. 7

7.1

Default Settings .................................................................................... 8

7.2

Device Configuration Utility

................................................................ 8

7.2.1

Terminal Tab................................................................................. 9

7.2.2

Setting Editor Tab ....................................................................... 11

7.2.3

Downloading a New Operating System ...................................... 11

7.3

Datalogger/RTU Connection ............................................................. 12

7.3.1

SDI-12 Wiring ............................................................................ 13

7.3.2

RS-232 Wiring ............................................................................ 13

7.3.3

Analog 0 to 5 Volt Wiring .......................................................... 14

7.4

Programming ...................................................................................... 14

7.4.1

SDI-12 ......................................................................................... 15

7.4.2

RS-232 ........................................................................................ 15

7.4.3

Analog ......................................................................................... 15

7.5

Mounting Suggestions ........................................................................ 15

7.5.1

Mounting Example ..................................................................... 16

Operation .................................................................. 18

8.1

Turbidity Units ................................................................................... 18

8.2

Vertical-Cavity Surface-Emitting Laser Diode .................................. 19

8.3

OBS500CBL-L Connector Pin Out ................................................... 20

8.4

Measurements .................................................................................... 20

8.5

Communication Modes ...................................................................... 21

8.5.1

SDI-12 ......................................................................................... 21

8.5.1.1

Measuring Multiple SDI-12 Sensors ................................ 23

8.5.2

RS-232 ........................................................................................ 23

Содержание OBS501



































































Результаты поиска

Содержание OBS501

Отзывы:

Похожие инструкции для OBS501

Бренды по названию

Популярные бренды

Campbell OBS501, Руководство оператора

Результаты поиска

Содержание OBS501

Отзывы:

Похожие инструкции для OBS501

Бренды по названию

Популярные бренды