Campbell NR-LITE2 Скачать руководство пользователя страница 7

Страница: 7 / 25

NR-LITE2 Net Radiometer

1. Introduction

The NR-LITE2 is a high-output thermopile sensor that measures the algebraic

sum of

incoming and outgoing all-wave radiation (both short-wave and long-

wave components). Incoming radiation consists of direct (beam) and diffuse

solar radiation plus long-wave

irradiance from the sky. Outgoing radiation

consists of reflected solar radiation plus the

terrestrial long-wave component.

The NR-LITE2 is equipped with PTFE-coated (polytetrafluoroethylene) sensor

surfaces. This results in a robust design

which provides easy maintenance and

good sensor stability. However, this design is slightly

less accurate than the

more traditional radiometers which use plastic domes.

This manual provides information only for CRBasic data loggers.

For retired Edlog data logger support, see an older manual at

www.campbellsci.com/old-manuals

2. Precautions

•

READ AND UNDERSTAND the

Safety

section at the front of this

manual.

•

Although the NR-LITE2 is rugged, it is also a highly precise scientific

instrument and should be handled as such.

•

Care should be taken when opening the shipping package to not damage or

cut the cable jacket. If damage to the cable is suspected, contact Campbell

Scientific.

•

When installing the NR-LITE2, use only the support arm to rotate the NR-

LITE2. Using the sensor head to rotate the instrument may damage it.

3. Initial Inspection

•

Upon receipt of the NR-LITE2, inspect the packaging and contents for

damage. File damage claims with the shipping company.

•

The model number and cable length are printed on a label at the

connection end of the cable. Check this information against the shipping

documents to ensure the correct product and cable length are received.

•

Refer to Section

3.1

Ships With

(p. 1)

, to ensure that parts are included.

3.1 Ships With

(1) WRR traceable calibration certificate

(1) Mounting arm from original manufacturer

(1) Bird stick from original manufacturer

NOTE

Содержание NR-LITE2

























Результаты поиска

Содержание NR-LITE2

Отзывы:

Бренды по названию

Популярные бренды

Campbell NR-LITE2, Руководство по эксплуатации продукта

Результаты поиска

Содержание NR-LITE2

Отзывы:

Бренды по названию

Популярные бренды