Burner Clean-out
Before each use the burner should be cleaned out by lifting
the pullout lock and pulling the clean-out port knob on the
right side of the grill to open the burner clean-out. This will
allow the ash from previous use to fall into the cup under
the grill. The cup should be removed and emptied and then
reinstalled before each use.
DANGER
Never Operate the Pellet grill without the ash cup in place.
Make sure the burner clean-out port is closed and locked
before starting the grill.
WARMING RACK
COOKING GRATE
CLEANOUT PORT KNOB
CLEANOUT PORT KNOB
Never open the burner clean-out port when the grill is hot.
After cleaning out the burner make sure to close the burner
clean-out by pushing the clean-out port knob in on the right
side of the grill. Make sure to lift the pullout lock and push
the clean-out port knob all the way in and lock in place
with the pullout lock. Every 50 hours of use, remove the grill
grates, grease tray, and heat deflector and clean the inside
of the grill. If you notice a lot of ash blowing around in the
grill it is time to vacuum it out.
Filling the Auger Tube
Caution: Only use the feed setting when hopper has run
out of pellets. Feed setting is not for normal use.
The first time you use your grill or any time the hopper has
run out of pellets you will need to fill the auger tube. This
simply means you must fill the auger tube with pellets until
pellets reach the burner. This is done by selecting FEED from
the main menu: With the controller powered on press the
selector knob to enter the MENU. Rotate the knob until FEED
is shown and press the selector knob again. This will turn
the auger on and the controller will display "FEED" and a
countdown timer. The auger will remain on for no more than
7 minutes. This is ample time for the pellets to reach the
burner. To avoid over-filling of the burner with pellets, open
the burner clean-out by pulling the knob on the right side of
the grill, opening the clean-out slide. Once you hear pellets
dropping into the ash cup you can close the clean-out by
pushing the knob on the right side of the grill. FEED mode
can then be cancelled from the controller by rotating the
selector knob and pressing it, to confirm the cancel (Never
operate the grill without the ash cup in place). Always make
sure the burner clean-out port is closed by pushing in the
knob on the right side of the grill before selecting any of the
cook settings. Never open the burner clean-out port when
the grill is hot.
Emptying the Hopper
This grill is equipped with a hopper drain to quickly remove
the pellets from the hopper. This can be used to remove
pellets if the grill is being stored for a long time or to remove
pellets to change to a different flavor pellet.
Warning:
Never remove the auger guard from the hopper
while the pellet grill is on. Never operate the grill without the
auger guard in place.
Caution:
The instructions below must be followed when
emptying the hopper.
1. Unplug the grill from the power source.
2. Hang a bucket or use a box to catch the pellets that will
come out of the tube on the rear of the hopper.
3. Lift the pull-out lock on the left side of the hopper and pull
the hopper clean-out knob.
4. Sweep the remaining pellets in the hopper towards the
drain hole.
5. Push in the hopper clean-out knob and lock in place using
the pull-out lock.
FIG. 21
HOPPER CLEANOUT
App quick start guide (Optional)
1. Download the Camp Chef APP from the Apple APP store or
Android Play Store.
2. Turn the Grill controller on using the main power switch.
3. Open the Camp Chef APP and follow the setup instructions
for connecting the grill to your home 2.4 GHz WiFi network.
Warning - Do NOT leave this appliance unattended while
in use. The user must remain in the immediate area of the
product and have a clear view of the product at all times
during operation.
Note - Some functions are only available from the controller.
