Cameron 351 Скачать руководство пользователя страница 4

Страница: 4 / 36

Section 1

Model 351/352/353 Liquid Level Systems

Product Description

Model 351 Liquid Level System

The Model 351 consists of a

single reference sensor

connected by capillary

tubing to a Barton Differential Pressure Unit (DPU). Hydraulic fluid is sealed

inside the sensor and the capillary tubing, eliminating the need for additional

piping.

The Model 351 system, as shipped from the factory, needs only to be mount-

ed on the vessel to provide continuous level measurement when used with a

Barton readout instrument. The sensor can be installed on vented or sealed

process vessels. The readout instrument (DPU, for example) can be installed

at various elevations (i.e., below the vessel, at the vessel upper connection or

above the vessel ) as long as the instrument calibration considers the elevation

difference between the instrument and the sensor.

Model 352 Liquid Level System

The Model 352 consists of

two reference sensors

connected by capillary tub-

ing to a Barton DPU.

Unlike the Model 351 system, the process media does not come into contact

with the DPU, making the model ideal for applications involving corrosive

liquids or tank temperatures above 200°F (95°C).

The DPU can be mounted up to 50 ft (15 meters) away from the vented or

sealed process vessel and at ele vations up to 30 ft (9 meters) above the lowest

sensor. Elevation of the readout instrument (DPU) with respect to the sensors

is essentially unlimited as long as the instrument calibration considers the

elevation difference between the two sensors.

Model 351/352 System Sensors

A Model 351 or Model 352 system can include any of three sensor types,

depending on the pressure rating required:
•

500-psi SWP sensor (referred to as Model 351 sensor throughout this

document)

•

3,000-psi SWP sensor (referred to as Model 351 sensor throughout this

document)

•

No-pressure-rating sensor (referred to as Model S048 sensor throughout

this document)

All three sensor types contain a 3.75” (95 mm) bellows that functions as a

seal. As pressure on the bellows varies due to changes in liquid level and/or

process system pressure variations, these pressure variations are transmitted

through the liquid filled sensor and capillary tubing to the readout instrument.

Содержание 351





































Результаты поиска

Содержание 351

Отзывы:

Похожие инструкции для 351

Бренды по названию

Популярные бренды

Cameron 351, Руководство по установке

Результаты поиска

Содержание 351

Отзывы:

Похожие инструкции для 351

Бренды по названию

Популярные бренды