p.
88
- M
an
u
al
c
o
d
e:
3
1
9
W
7
6
31
9
W
76
v.
11
0
6
/2
0
1
4 © C
A
M
E S
.p
.A
. - T
h
e d
at
a a
n
d i
n
fo
rm
at
io
n i
n t
h
is
m
an
u
al
m
ay b
e c
h
an
g
ed a
t a
n
y t
im
e a
n
d w
it
h
ou
t n
ot
ic
e.
TOTAL STOP from button (contact 1-2)
By default, the feature is enabled.
To disable it:
select the DIPs as shown and press the PROG key on the board. The LED flashes and the buzzer sounds off twice.
To return to the default setting, press PROG again. The LED stays on and the buzzer sounds off for 1 s.
Self-learning of the gate travel (see Self-learning paragraph)
Select the DIPs as shown and press the PROG key on the board.
The gate will perform a series of maneuvers to determine the endstop points. To establish the opening and closing
slow-down points, press PROG at the moment when the gate leaves reach the points you want.
During calibration the PRG LED flashes. Once calibration is finished, the buzzer sounds off for 1 s.
If the calibration is not successful, the LED flashes quickly and the buzzer sounds off 7 times.
You can interrupt the gate travel's self-learning operation by pressing the STOP button (if enabled).
Reopening during closing (contact 2-C1)
By default, the feature is disabled.
To enable it:
select the DIPs as shown and press the PROG key on the board. The LED stays on and the buzzer sounds off for 1 s.
To return to the default setting, press PROG again. The LED flashes and buzzer sounds off twice.
Input on contact 2-CX
By default, the feature is disabled.
To enable it:
select the DIPs as shown and press the PROG key on the board. The LED stays on and the buzzer sounds off for 1 s.
To return to the default setting, press PROG again. The LED flashes and buzzer sounds off twice.
Partial stop or obstruction wait (contact 2-CX)
By default, the feature is on partial stop.
To enable on obstruction wait:
Select the DIPs as shown and press the PROG key on the board. The LED stays on the buzzer sounds off for 1 s..
To return to the default setting, press PROG again. The LED flashes and the buzzer sounds off twice.
OPEN-CLOSE-INVERT or OPEN-STOP-CLOSE-STOP with button (contact 2-7)
By default, the feature is OPEN-CLOSE-INVERT.
To enable it to OPEN-STOP-CLOSE-STOP:
select the DIPs as shown and press the PROG key on the board. The LED stays on and the buzzer sounds off for 1 s.
To return to the default setting, press PROG again. The LED flashes and the buzzer sounds off twice.
. Button activated partial opening or pedestrian opening (contact 2-3P)
BY default, the opening is set to pedestrian mode.
To enable in partial opening:
select the DIPs as shown and press the PROG key on the board. The LED stays on and the buzzer sounds off for 1 s.
To return to the default setting, press PROG again. The LED flashes and buzzer sounds off twice.
Obstruction detection with motor stopped
By default, the feature is enabled.
To disable it:
select the DIPs as shown and press the PROG key on the board. The LED flashes and the buzzer sounds off twice.
To return to the default setting, press PROG again. The LED stays on and the buzzer sounds off for 1 s.
Encoder
By default, the feature is enabled.
To disable it:
select the DIPs as shown and press the PROG key on the board. The LED flashes and the buzzer sounds off twice.
To return to the default setting, press PROG again. The LED stays on and the buzzer sounds off for 1 s.
Timed slow-downs (with Encoder disabled
)
By default, the feature is disabled.
To enable it:
select the DIPs as shown and press the PROG key on the board. The LED flashes and the buzzer sounds off for 1
s. To return to the default setting, press PROG again. The LED flashes and the buzzer sounds off twice.
Automatic closing
By default, the feature is disabled.
To enable it:
select the DIPs as shown and press the PROG key on the board. The LED stays on and the buzzer sounds off for 1 s.
To return to the default setting, press PROG again. The LED flashes and the buzzer sounds off twice.
The wait before automatic closing starts when the opening endstop point is reached for a time that is adjustable by
the A.C. T. trimmer.
⚠
The automatic closing does not activate if the safety devices are triggered due to obstacle detection, after a total
Stop or if the current is missing.
